Ring 48, Macro led ring light, Instruction manual – Godox RING48 Macro Ring LED Light User Manual
Page 2
5. Specifications:
Effective Distance
Power Rate
Service Time
(2 AA Nickel-hydrogen Batteries)
Size
Weight
3cm
-1
00cm
(1.1-40
inches
)
Semi Power, Full Power
About 1.5 hours
①
Power Controller:
9.1*4.4*4.4 cm
②
M
acro Ring Flash:
12.8*10.3*2.8 cm
165g (without batteries)
48 PCS
5500K ~ 6500K
LED
Color Temperature
1) Avoid clash or falling when used.
2) Do not use the flash in extreme high or cold temperature or in
dampness.
3) Do not clean the stains or fingerprint with thinner, benzene or other
detergents. Clean the light with soft wet cloth.
4) If the light comes from a
colder room to a
warmer room, condensation
will happen inside LED light and can damage the product. Do not use
the product until it reaches the room temperature.
5) Keep it in dry, cool place with good ventilation when not used.
We keep improving our products to meet the need of market, so
any subtle
changes
may
not
be
updated
in the
manual
.
Sorry for
the inconvenience.
Macro ring head 1PC
Charger 1PC
Power controller 1PC
Adapter ring 6PCS (49mm
,
52mm
,
55mm
,
58mm
,
62mm
,
and
67mm
)
6. Contents:
7. Notice:
Important notes
#
Due to its high power consumption, we strongly recommend rechargeable
batteries. If common 1.5V battery is used, the light
effect will be
d
immer
and the service time shorter.
#
Turn off the power when the
ring
l
ight
i
s
not used due to the high power
consumption.
1
）
Power Controller Installation
Attach
hot
shoe
onto the camera hot shoe mount and rotate to
tighten the hot shoe locker ring.
2
）
Installation of Macro
Ring
light
head to the camera
6 types of adapter rings available
to
suit
the
camera
lens
:
49mm
,
52mm
,
55mm
,
58mm
,
62mm
,
and
67mm
.
3) How to Use
A. Power Supply By Battery
Install the battery and switch the power controller to
“
BATT
”
B. Power Supply By Charger
Insert the round plug of charger into the
'
DC3V
'
of
power
controller
,
and
connect
the
other
end
with
the
AC
power
.
And then turn the
power switch of power controller to
“
DC3V
”.
Warning:
Do not leave
the
rechargeable
battery
in
the
power
controller
when
it
is
being
charged
.
4
) Lens Usage
Designed for Macro-lens, the LED light can be used with other types
of lens, but please take note the followings:
Some lens might turn after the installation of this LED
ring
h
ead,
which may affect camera focusing. Please use manual focus when
apply this kinds of lens.
LED
4. Using Method:
1. Names of Principal Parts
①
Battery Pack
②
Power Output Jack
③
3V DC Power Input Jack
④
Power Indicator
Lamp
⑤
Hot Shoe
⑥
Power and Power Mode Controller
Off
:
Power
Off
DC
3
V
:
Power Supply By Charger
Batt
:
Power Supply By Battery
2 ways of power supply are available for this Macro
Ring light:
1) 2 AA alkaline dry batteries or rechargeable Ni-MH batteries
.
2) Exclusive
charger for 3V power supply.
Warning: This charger is only used for LED light
.
Do not use it for
the rechargeable battery
LED
2. Power Matters:
3. Attention:
1) Clean
the
ends
of
battery
to
make
sure
the
good
connection.
To
avoid
battery
explosion
,
fluid
leakage
or
overheating
,
please use the
same model and brand new two AA batteries, not to mix old and new
batteries or different models for use .
2) Do not dismantle or drain batteries or put batteries in water or fire,
which may cause explosion. Do not charge the batteries except
lithium and cadmium cell.
3) Remove
the
batteries
if
you
don
'
t use the lamp for a long time.
⑦
Charger Input Plug
⑧
Charger 3V Output Plug
⑨
Ring
Head
Power
Input
Plug
⑩
LED Mode Controller
RING
48
Macro LED Ring Light
Instruction Manual
Macro LED Ring Light
WWW.GODOX.COM