Parkside PZKS 1500 A1 - Manual (Page 14)

9 GB
8.5 Precision adjustment of the stop for mitre cut
45° (Fig. 1/10/11)
• No stop angle included.
• Lower the machine head (4) and secure using the
locking bolt (23).
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1) to
angle the machine head (4) 45° to the left.
• 45° - position angle stop (b) between the saw blade
(6) and rotary table (14).
• Adjust the adjusting screw (28) until the angle be-
tween the saw blade (6) and rotary table (14) is pre-
cisely 45°.
• It is not necessary to fix this setting because it is
maintained by the spring pretension.
• Subsequently check the position of the angle indi-
cator. If necessary loosen the pointer (19) using a
Philips screwdriver, set to position 0° on the angle
scale (18) and re-tighten the retaining screw.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/12)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
•
Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1)
to angle the machine head (4) to the left, until the
pointer (19) indicates the desired angle measure-
ment on the scale (18).
• Re-tighten the fixing screw (22).
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 2/4/13)
The crosscut saw can be used to make mitre cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the
right in relation to the stop rail (double mitre cut).
•
Move the machine head (4) to its upper position.
• Release the rotary table (14) by loosening the set
screw (26).
• Using the handle (11), set the rotary table (14) to the
desired angle (refer also to point 8.4 in this regard).
• Re-tighten the set screw (26) in order to secure the
rotary table.
• Undo the locking screw (22) and use the handle (1)
to tilt the machine head (4) to the left until it coin-
cides with the required angle value (in this connec-
tion see also section 8.6).
• Re-tighten the fixing screw (22).
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 3/14)
•
The cutting depth can be infinitely adjusted using the
screw (24). To do this loosen the knurled nut on the
screw (24). Move the stop for the cutting depth limi-
tre (25) to the outside. Turn the screw (24) in or out
to set the required cutting depth. Then re-tighten the
knurled nut on the screw (24).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 1)
The saw is equipped with a debris bag (17) for saw-
dust and chips.
Squeeze together the metal ring on the dust bag and
attach it to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a zip-
per at the bottom.
8.10 Changing the saw blade (Fig. 15/16/17/18)
Remove the power plug!
Important.
Wear safety gloves when changing the saw blade.
Risk of injury!
•
Swing up the machine head (5).
• Undo the screw (e) on the guide bar (37), so that it
can move freely and be pivoted downwards.
• Press the release lever (3). Swing up the saw blade
guard (6) to the point where the recess in the saw
blade guard (6) is above the flange bolt (31).
• Press the saw shaft lock (4) with one hand. With the
other hand insert the allen key (c) in the flange bolt
(31).
• Hold the Allen key (d) and slowly close the saw bla-
de guard until it touches the Allen key.
• Firmly press the saw shaft lock (4) and slowly rotate
the flange bolt (31) in clockwise direction. The saw
shaft lock (4) engages after no more than one rota-
tion.
• Now, using a little more force, slacken the flange
bolt (31) in the clockwise direction.
• Turn the flange screw (31) right out and remove the
external flange (32).
• Take the blade (7) off the inner flange (38) and pull
out downwards.
• Carefully clean the flange screw (31), outer flange
(32) and inner flange (38).
• Fit and fasten the new saw blade (7) in reverse or-
der.
• Important! The cutting angle of the teeth, in other
words the direction of rotation of the saw blade (7)
must coincide with the direction of the arrow on the
housing.
• Move the guide bar (37) into position and tighten the
screw (e) again.
• Before continuing your work make sure that all safe-
ty devices are in good working condition.
• Important! Every time that you change the saw
blade (7), check to see that it spins freely in the ta-
ble insert (11) in both perpendicular and 45° angle
settings.
• Important! The work to change and align the saw
blade (7) must be carried out correctly.
8.11 Using the laser (Fig. 3/19/20/21)
•
To switch on: Move the ON/OFF switch of the laser
(34) to the “1” position. A laser line is projected onto
the material you wish to process, providing an exact
guide for the cut.
• To switch off: Move the ON/OFF switch of the laser
(34) to the “0” position.