Marantz SR4023 - Manual (Page 10)

7
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTIONS
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND FUNCTIONS
ENGLISH
i REMOTE CONTROL IN/OUT
terminals
Connect to a Marantz component equipped with
remote control (RC-5) terminals.
o Speaker terminals
Connect your speaker system(s) to these terminals.
There are two sets of terminals, so you can connect
either A and/or B speaker systems.
!0 Subwoofer Output
Connect this jack to the line level input of a powered
subwoofer.
!1 MAIN IN jacks
Use these jacks to connect an extension pre amplifi er.
(See page 13)
When not used, leave these jacks connected with the
supplied connecting pins.
!2 PRE OUT jacks
Use these jacks to connect an extension power
amplifi er. (See page 13)
When not used, leave these jacks connected with the
supplied connecting pins.
!3 AUDIO IN/OUT
(PHONO, CD, RECORDER 1,
RECORDER 2)
These are the analog audio inputs and outputs. There
are 8 audio inputs (4 of which are linked to video
inputs) and 3 audio outputs (1 of which is linked to
video output). The audio jacks are nominally labeled
for recorder1 (CD recorder) recorder2 (cassette tape
deck), compact disc players, DVD players and etc....
The audio inputs and outputs require RCA-type
connectors.
!4 GND (ground) terminal
Connect the grounding wire from the analog turntable
to this terminal.
REAR PANEL
t RS-232C
The RS-232C port is to be used in conjunction with
an external controller to control the operation of the
unit by using an external device.
y AC OUTLETS
Connect the AC power cord of component such as a
DVD or CD player to this outlet.
The marked SWITCHED provides power only when
the SR4023 is turned on and is useful for components
which you use every time you play your system.
Caution:
• In order to avoid potential turn-off thumps, anything
plugged into these outlets should be powered up
before the SR4023 is turned on.
• The capacity of this AC outlet is 150W. Do not
connect devices that consume electricity more than
the capacity of this AC outlet. If the total power
consumption of the connected devices exceeds the
capacity, the protection circuit shuts down the power
supply.
u AC IN
Connect to supplied an AC power cable, and connect
to an AC power outlet.
This unit requires a power voltage of 120V AC only.
q Antenna terminals
FM antenna terminal
For connecting the supplied FM antenna or for
connecting an external FM antenna with a coaxial
cable, or for connecting a cable network.
AM antenna and ground terminal
For connecting the supplied AM loop antenna. Use
the terminals marked “AM” and “GND”.
The supplied AM loop antenna will provide good AM
reception in most areas. Position the loop antenna to
the best reception.
w VIDEO IN/OUT
(AUX, DSS, DVD, VCR)
These are the video inputs and output. There are 4
video inputs and 1 video output. Connect VCR, DVD
players, and other video components to the video
inputs.
The 1 video output can be used to be connected to
video tape recorder for making recording.
e MONITOR output jack
Connect to the TV’s video input (VIDEO IN) jack.
r FLASHER IN (Flasher input
terminal)
This terminal is to control the unit from another
zone.
Connect the control signal from a Keypad, etc.
REMOTE CONTROL REMOTE CONTROL AUX AUX DSS DSS DVD DVD VCR VCR
IN IN IN IN OUT OUT IN IN OUT OUT
DSS DSS DVD DVD
VIDEO VIDEO
VCR VCR AUX AUX MONITOR MONITOR
IN IN
IN IN IN IN IN IN IN IN IN IN IN IN OUT OUT OUT OUT IN IN IN IN OUT OUT
PHONO PHONO
GND GND
L L
R R
SUB SUB WOOFER WOOFER PRE PRE
OUT OUT
CD CD PRE PRE
OUT OUT RECORDER 2 RECORDER 2 ( (TAPE TAPE) ) MAIN MAIN IN IN RECORDER 1 RECORDER 1 ( (CD-R CD-R) )
AUDIO AUDIO
RS-232C RS-232C
R R
R R
L L
L L
AC IN AC IN
CLASS 2 WIRING CLASS 2 WIRING
GND GND AM AM FM FM ( (75 75 Ω Ω))
ANTENNA ANTENNA
MODEL NO. SR4023 MODEL NO. SR4023
IN IN
OUT OUT
A A SYSTEM SYSTEM
B B SPEAKER SYSTEMS SPEAKER SYSTEMS
SYSTEM SYSTEM
FLASHER FLASHER IN IN
UNSWITCHED UNSWITCHED 1.25A 150W 1.25A 150W
AC OUTLETS AC OUTLETS 120V 60Hz 120V 60Hz
SWITCHED SWITCHED
1.25A 150W
1.25A 150W
q y w u
i o !0 !3 !1 !2 !4
e r t