Whirlwind W2 61 - Manual

Whirlwind
W2 61 Pin Connector System
Technical Data
Materials and
Finishes:
• Contacts: Copper alloy,
hard gold plate over
nickel under plate per
MIL-G-45204
• Insulators: Low temperature
elastomer
• ‘O’ Rings and Seals:
Low temperature elastomer
• Shells and Dust Caps:
All aluminum alloy, black
anodized coating
Chain-Stainless steel
Mechanical Data:
• Operating Temperature:
-40°C to +105°C
-40°Fto -t-221°F
• Contacts: #20 AWG Solder
type (7.5 Amp rating)
• Contact Retention:
15 lbs. minimum
• Connector Engagement
and Separation Forces:
44 in. lbs. maximum
• Polarization: 5 Keyways
Electrical Data:
• Operating Voltage: 850
VDC or 600 VAC rms
maximum
• Insulation Resistance:
5000 megohm minimum
• Contact Resistance:
6 milliohms maximum
The Whirlwind W2 is a 61 contact, quick disconnect connector
system based on the proven MIL-26482 multipin standard. The pin
and socket modules are shell size 24 with a standard 61 contact
insert arrangement. The solder style contacts are permanently
mounted in resilient rubber insulators to provide years of trouble
free service.
Whirlwind manufactures a robust aluminum backshell to protect
the soldered connections and provides a waterproof mesh grip for
an absolutely reliable strain relief on the cable. The W2 system
utilizes a 61 pin male insert in a plug shell, with a quarter-turn
locking ring and a 61 socket female insert in a receptacle shell with
studs, that mates with the male plug shell.
Whirlwind provides the W2 in four standard configurations, male
and female inline and male and female chassis mount. The W2 can
be used to interconnect up to 20 balanced, shielded signal lines.
W2CF Female Panel Connector / Cap, Wiring Kit Complete
AB60FP 61 Pin Female Panel Mount Body with Studs 1
AB60CAP Dust Cap with Ring For Female 61 Pin 1
PT1-16BK-1.5 Drain Wire Insulator 1/16” BIk Shrink Tube 1.5” 20
PT3-16BK-1.0 Mylar / Foil Insulator 3/16” BIk Shrink Tube 1.0” 20
PT1-16BK-0.5 Solder Cup Insulator 1/16" BIk Shrink Tube 0.5” 60
W2 Pin Out Wiring Diagram For 61 Pin 1
W2CM Male Panel Connector / Cap, Wiring Kit Complete
AB60MI 61 Pin Male Inline Body with Ring 1
AB60CAPWT Dust Cap with Studs For Male 61 Pin 1
AB60MPA Panel Mount 61 Pin BIk Flange with Set Screw 1
PT1-16BK-1.5 Drain Wire Insulator 1/16” BIk Shrink Tube 1.5” 20
PT3-16BK-1.0 Mylar / Foil Insulator 3/16” BIk Shrink Tube 1.0” 20
PT1-16BK-0.5 Solder Cup Insulator 1/16” BIk Shrink Tube 0.5” 60
W2 Pin Out Wiring Diagram For 61 Pin 1
W21F Female Inline Connector / Cap, Wiring Kit Complete
AB60FI 61 Pin Female Inline Body with Studs 1
AB60CAP Dust Cap with Ring For Female 61 Pin 1
AB60H 61 Pin Inline Housing with Set Screws 1
AB60G 39-61 Inline Strain Relief Grip Range .375”-.50” 1
ABKR 16mm Split Ring For Dust Cap Chain 1
PT1-16BK-1.1 Drain Wire Insulator 1/16” BIk Shrink Tube 1.1” 20
PT3-16BK-0.5 Mylar / Foil Insulator 3/16" BIk Shrink Tube 0.5” 20
PT1-16BK-0.5 Solder Cup Insulator 1/16” BIk Shrink Tube 0.5” 60
W2 Pin Out Wiring Diagram For 61 Pin 1
W2IM Male Inline Connector / Cap, Wiring Kit Complete
AB60MI 61 Pin Male Inline Body with Ring 1
AB60CAPWT Dust Cap with Studs For Male 61 Pin 1
AB60H 61 Pin Inline Housing with Set Screws 1
AB60G 39-61 Inline Strain Relief Grip Range .375”-.50” 1
ABKR 16mm Split Ring For Dust Cap Chain 1
PT1-16BK-1.1 Drain Wire Insulator 1/16” BIk Shrink Tube 1.1" 20
PT3-16BK-0.5 Mylar / Foil Insulator 3/16” BIk Shrink Tube 0.5” 20
PT1-16BK-0.5 Solder Cup Insulator 1/16" BIk Shrink Tube 0.5” 60
W2 Pin Out Wiring Diagram For 61 Pin 1
Inline kits available w/ DCG75-3/4 Oversize Strain Relief (grip range .75" - .875").
W2IF-OS Female Kit same as W2IF Kit (above) except with one DCG75-3/4.
W2IM-OS Male Kit same as W2IM Kit (above) except with one DCG75-3/4.
'q^
I r o ° i
° o °o
3° 1 11
11° o“ o
\\WnO o
'\\\° o„ '
0^0
o°o o////
o/ j a
/ / / / / /
r 1
---------- -------- 1.6’ ----------
^ 61 pin Inline Male
61 Pin Chassis Male
Q ________ Q Drain wire Solder cup insulator Foil insulator
3.24’
(3.72’ with dust cap in place)
(Strain relief bushing adds approximately 2’ to rear of connector)
^ 1.35’ (with dust cap in place) -
61 Pin Chassis Female
(Chassis connectors
0 .147’ for 46 screw
0 .172" for 48 screw
Cable
Preparation
Diagram
mount on front of panel) g., p¡„
(,,,35515