Virtual tach system, Tach programming – Autostart AS-3372 TW-FM User Manual
Page 3
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Virtual Tach System
* Virtual Tach System combines the latest microcontroller technology and a complex algorithm that took years to develop.
VTS is able to effectively monitor the engine starting sequence and release the starter at the right time without physically
connecting the tach wire to the remote starter. The VTS constantly monitors the data and readjusts itself automatically in order
to maximize its capability to start the engine properly in any weather or deteriorating battery condition
(automatic transmission
only).
Optional Time Delay Adjustment in Virtual Tach System
Follow these steps to program crank time adjustment, if needed:
1.
Enter programming mode {see p.
1)
— the parking lights will stay on for up to 20 seconds.
2.
Before the lights go out, press and hold the brake pedal and press the LOCK and UNLOCK buttons simultaneously — the
parking lights will flash 4 times.
Do not release the brake pedal.
3.
Press the
LOCK
button if you wish to increase the time delay or the
UNLOCK
button if you want to decrease it.
The time
delay will be increased or decreased by 50ms. and the parking lights will flash once every time the LOCK or UNLOCK
button is pressed.
4. Press the
TRUNK
button to save the settings you have entered.
5. Release the brake pedal - the time delay programming is now complete.
Tach Programming
1.
Enter programming mode (see p.
1)
— the parking lights will stay on for up to 20 seconds.
2. Before the lights go out, press and hold the brake pedal and press the LOCK and UNLOCK buttons simultaneously—the
parking lights will flash 4 times At that point, release the brake pedal.
3. Start up the engine and allow the vehicle to reach regular engine idle speed.
4. Once the engine is running at normal idle speed, press the brake pedal and keep it down until you hear the parking lights
output click 5 times.
5. Release the brake pedal —^the tach programming is now complete.
Horn Honk Timing
Supplementary Information
Fifth Relay Output (2nd IGN, ACC or CRANK)
Remote car starters of this series are equipped with an on-board high
current programmable 5
th
relay that can be used to power a second
ignition, accessory or crank wire. The unit uses 3 sets of pins; each set
corresponds to a specific function of the output. In order to activate
one of the three possible functions, you must place the jumper
(supplied) on one of the three sets of pins and connect the l4 AWG
wire to the second
IGN. / ACC. / CRANK
wire of the vehicle.
Installation Guide
To trigger
AUX 2
: press the
START/STOP
button. Must have configured option 1 or option 2
in menu 3 feature 3 (
AUX 2
).
FEATURE 2 - Engine Run Time
OPTION 1
Run Time = 3 minutes in
gas
mode / 8 minutes
diesel
mode
OPTION 2*
Run Time = 15 minutes in gas mode / 20 minutes diesel mode
OPTION 3
Run Time = 25 minutes in
gas
mode / 30 minutes
diesel
mode
FEATURE 3 - Idle Mode & Turbo Mode (auto) / Turbo Mode (manual)
OPTION 1
Idle mode & turbo mode
DISABLED (AUTO)
/ turbo mode
DISABLED (MANUAL)
OPTION 2*
Idle mode & turbo mode ENABLED (AUTO) / turbo mode DISABLED (MANUAL)
OPTION 3
Idle mode & turbo mode
ENABLED (AUTO)
/ turbo mode
ENABLED (MANUAL)
FEATURE 4 - Engine type and Cold Weather Mode
OPTION 1
Diesel mode with 20-minute run time in cold weather mode (30-sec. wait to start delay)
OPTION 2*
Gas mode with 3-minute run time in cold weather mode
OPTION 3
Diesel mode with 8-minute run time in cold weather mode (18-sec. wait to start delay)
OPTION 4
Diesel mode with 8-minute run time in cold weather mode (7-sec. wait to start delay)
FEATURE 5 - Ignition Valet
OPTION 1
Ignition valet -
DISABLED
OPTION 2*
Ignition valet - ENABLED
MENU 3 *
indicates default setting
FEATURE 1 - Home Valet
OPTION 1
Home Valet
ENABLED
OPTION 2*
Home Valet DISABLED
FEATURE 2 - AUX 1 Programming
OPTION 1
Horn confirmation upon the 2
nd
press of the
LOCK
button
OPTION 2*
Priority door access
OPTION 3
Horn confirmation upon the 1
st
press of the
LOCK
button
FEATURE 3 - AUX 2 Programming
OPTION 1
Constant output while pressing
AUX
followed by
LOCK
In safe start mode: activate
AUX 2
by pressing the
START
/
STOP
button
OPTION 2*
Toggle ON/OFF (with 30-second time out)
OPTION 3
Toggle
ON/OFF
(with 4-minute time out) ^active when under remote run
OPTION 4
Priority door access
FEATURE 4 - AUX 3 / Zone 3 Programming
OPTION 1
1-sec. output when
TRUNK
button is pressed for 3 sec. with ignition
OFF
or under
remote run & data output (channel expander MCX-100 enabled)
OPTION 2*
Constant output while the TRUNK button is pressed
OPTION 3
Disarm/rearm pulse with
TRUNK
& data output (channel expander MCX-100 enabled)
FEATURE 5 - External Trigger
OPTION 1
Zone 3 disarm/rearm (trunk pin: a disarm pulse is sent before the trunk opens; the vehicle
rearms 4 seconds after the trunk is closed).
OPTION 2*
Key sense
OPTION 3
Engine start / stop
OPTION 4
Pager
MENU 4 *
indicates default setting
FEATURE 1 - Multi-Level Features
OPTION 1
Multi-car Features, Basic Features, Customized Features
OPTION 2*
Basic Features, Multi-car Features, Customized Features
OPTION 3
Customized Features, Multi-car Features, Basic Features
OPTION 4
Basic Features, Customized Features, Multi-car Features
FEATURE 2 - Alarm Control
OPTION 1
ENABLED
(
HORN
must be enabled in MENU 3 FEATURE 2, option 1 or 3)
OPTION 2*
DISABLED
FEATURE 3 - Ready Mode Option
OPTION 1
Enabled by handbrake
OPTION 2*
Enabled by remote
FEATURE 4 - Bypass
OPTION 1
ADS
OPTION 2*
Trilogix
OPTION 3
Fortin
FEATURE 5 - Bypass Type
OPTION 1
One-Way communication
OPTION 2
Two-Way communication
Installation Guide
P. 6
P. 3