beautypg.com

GE 45216 GE Portable Security Kit User Manual

Portable security kit, User's manual, Instrucciones

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

A

warning

Risk of personal injury
• Prolonged exposure to

alarm siren may cause
permanent hearing loss

On/Off

Indicator

Battery Test
Light

Battery

Magnetic

Window Alarm

Indoor Use Only

120dB alarm saunds when

magnetic cantact is braken

On/Off switch and law battery push buttan

hidden in campartment

Indicatar far armed/disarmed status

Easy ta install - na wiring necessary

GAP BETWEEN ALARM AND MAGNETIC SENSOR

Alarm is activated when switched ON and gap

between alarm and magnetic sensor is

greater than 0.5".

BATTERY TESTAND INSTALLATION

The GE Magnetic Window Alarm requires (4) LR44

button batteries (included). Average battery life for

typical usage is up to one year. Magnetic

1. Slide cover off the battery Sensor

compartment

located

on

Siren

the front of the main unit.

2. Push the'Battery Test'

push-button in the battery

compartment. If the green

light illuminates, the battery Compartment

is still good. If it fails to illuminate, replace all

batteries.

3. Insert (4) LR44 button batteries noting polarity.

4. Replace battery compartment cover.

IMPORTANT:

Remove batteries before storing the

Alarm for extended periods. Batteries corrode over

time and may cause permanent damage to the unit.

Different types of batteries or new and used

batteries should not be mixed. Depleted batteries

should be removed and disposed of properly.

INSTALLATION

Using the douWe si'Bed a'BFiesive tape provided”

mount the alarm and magnetic sensor on window,

door, or cabinet to be protected, placing one of the

units on the part of the fixture that opens (window)

and the other unit on the stationary part of the

fixture (frame). Mount so that when the window, door

or cabinet is closed, the gap between the alarm and

sensor is no more than 0.5" (preferably less).

OPERATION

1. To arm the unit, slide cover off the battery

compartment located on the front of the main unit.

Toggle ON/OFF switch to the ON position. The

window on the housing will become red. Replace

battery compartment cover. Whenever the protected

window, door or cabinet is opened (causing the alarm

to be separated from the magnetic sensor by more

than 0.5"), the alarm siren will sound continuously

until disarmed.

2. To disarm the unit, slide cover off the battery

compartment. Toggle ON/OFF switch to OFF Position.

Make sure the window, door or cabinet is closed

before rearming.

NOTE:

To test, a cloth can be used to cover the alarm

to reduce risk of hearing damage.

CARE AND MAINTENANCE

To clean the unit housing, use a soft cloth slightly

dampened with water and wipe dry. Do not use

chemical agents as this may damage and discolor

the unit.

Pressure Activated
Door Stop Alarm

Indoor Use Only

Great travel alarm -

hatel raams, apartments

120dB alarm saunds when alarm is activated

A

warning

Risk of personal injury
• Prolonged exposure to

alarm siren may cause
permanent hearing loss

On-aff switch activates and deactivates alarm

Law-battery indicatar light

1

Battery

th

Compartment

y

[

[

Switch

Low Battery

Indicator

Metal Contact

Plate (Cover)

BATTERY INSTALLATION

The door stop alarm requires one 9V battery. When the

Low-Battery Indicator illuminates, batteries need replacing,

1. Toggle On/Off switch to the 'OFF' position to prevent

unintentional triggering.

2. Remove screw on the bottom of the door stop and

battery compartment cover.

3. Fit 9V battery to the connecting leaf, making sure the

terminal polarities are correct.

4. Replace cover.

IMPORTANT:

Remove batteries before storing the

Alarm for extended periods. Batteries corrode over

time and may cause permanent damage to the unit.

Depleted batteries should be removed from the unit

and disposed of properly.

TESTING THE ALARM

1. Toggle the On/Off switch to 'ON'.

2. Quickly but firmly tap down and release the metal on

the cover unit. A quick siren chirp indicates proper

operation. NOTE: A cloth can be used to cover the alarm

to reduce risk of hearing damage.

3. Toggle the On/Off switch to 'OFF'.

INSTALLATION:

Insert door wedge at the base of the door

as shown in the diagram, with the pointed edge under the

door gap. The alarm is properly installed if the alarm

sounds and the metal contact plate is depressed when

the door is opened. Make sure the non-skid pads on the

bottom of the alarm are in firm contact with the floor.

OPERATION

1. Toggle the On/Off switch to 'ON' to activate alarm.

2. Toggle the On/Off switch to 'OFF' to deactivate alarm.

CARE AND MAINTENANCE

To dean the unit housing,

use a soft cloth slightly dampened with water and wipe

dry. Do not use chemical agents as this may damage

and discolor the unit.

Personal

Security Alarm

120dB alarm saunds when pin

is remaved

Handy security alarm and light

gaes everywhere with yau

BAHERY INSTALLATION

Before using your Personal Key Chain

Alarm, remove the insulation tape

between the alarm housing and the

battery compartment. The Alarm requires (4) LR44

batteries (included). Test the batteries by the pushbutton

A

warning

Risk of personal injury
• Prolonged exposure to

alarm siren may cause
permanent hearing loss

on the leftside of the unit. Replace the batteries if the red

light does not illuminate. Average battery life for typical

usage is up to 6 months.

1. Access the battery compartment by removing the

three screws on the back of the unit and separating the

front and back halves of the alarm.

2. Insert (4) LR44 button batteries noting polarity.

3. Replace back of the alarm and secure with screws.

IMPORTANT!

Remove batteries before storing the Alarm

for extended periods. Batteries corrode over time and

may cause permanent damage to the unit. Do not mix

different battery types or new and used batteries.

Depleted batteries should be disposed of properly.

OPERATION OF ALARM, LIGHT

1. To activate siren, hold alarm in one hand and pull on

cord with the other, pulling metal pin out of alarm body.

2. To stop the siren, reinsert the metal pin back into the

alarm body.

3. To use light, press and hold button on left side of unit.

90 DAY LIMITED WARRANTY: Jasco Products Company warrants

this product to be free from manufacturing defects for a period of

ninety days from the original date of cansumer purchase. This

warranty is limited to the repair or replacement cf this prcduct only

and does not extend to consequential or incidental damage to other

products that may be used with this unit. This warranty is in lieu of

all other warranties express or implied. Some states do not allow

limitations on how long an implied warranty lasts ar permit the

exclusion or limitation of incidental or consequential damages, so

the above limitations may not apply to you. This warranty gives yau

specific rights, and yau may also have ather rights which vary fram

state to state. If unit should prove defective within the warranty

period, return prepaid with dated proaf of purchase to:

Jasco Products Company

311 N.W. 122nd

Oklahoma City, OK. 73114

45216-2 3/31/06

User's Manual

Instrucciones

Easy to Install

Portable

Security Kit

Equipo Portátil de Seguridad

fácil de instalar

DO NOT USE IN WET LOCATIONS

NO EMPLEE ESTOS PRODUCTOS

EN LUGARES MOJADOS

@ is a trademark of the General Electric

Company and is used under license to Jasco

Products Company LLC, 311 N.W. 122nd

Street, Oklahoma City, OK 73114.
www.jascoproducts.com