AeroBed Domed Valve - Manual

Thank you for joining the Aero® family by purchasing one of our upscale products. You can expect top-notch quality, innovation and imagination from every Aero
product.
You are about to enjoy the comfort of the AeroBed® Raised, the finest alternative sleeping system available anywhere. It is your responsibility to read and always
follow the safety, care and maintenance instructions for your new Aero product. Always instruct and supervise others on the proper use, maintenance and safety
of your bed.
IMPORTANT: Preperation of your AeroBed Raised requires no tools. Use of tools may damage your bed.
IMPORTANT SAFETY INFORMATION AND WARNINGS
- WARNING: Adult supervision required for inflation, deflation and maintenance. Follow all safety instructions to avoid serious injury.
-
WARNING: This is an electrical product-not a toy. To avoid risk of fire, burns, injury and shock, it should not be played with or placed where small
children can reach it. Do not use in or around water.
- WARNING: Product is for indoor use only.
- WARNING: For household/residential use only.
-This is not a water toy. Use as a mattress only.
-This mattress is not intended for infants or persons with limited mobility. They may roll off of the mattress and become entrapped between the mattress and a wall.
-Remove all sharp objects from area where bed will be set up and used.
-Do no step or jump on bed or use as a trampoline.
-Place bed in a safe area before use, making sure that there are no sharp edges, steps, or breakable items nearby. Use on flat surfaces only. Bed may tip over on
uneven surfaces.
-Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Protruding objects may puncture the bed.
-Do not sleep on the edges of the bed. Edges are less supportive and may crush under weight.
-This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters, open flame
or other hot objects.
-Unplug product when not in use.
-Do not attempt to dissemble, repair, or service the pump. No serviceable parts are contained inside.
Contact Aero Products International, Inc. at 1834 Walden Office Square, Suite 300, Schaumburg, IL 60173, for repair or servicing information.
INFLATION
Remove your AeroBed Raised from its lightweight duffel bag. Keep bag for storage.
1. Place your rolled-up bed on the floor free of obstructions or sharp objects.
2. Make certain the Quick Air Release Valve located at the foot of the bed is closed.
If the Quick Air Release Valve is open, close it by using 2 thumbs to push cover and snap into valve. Be careful to avoid pushing valve cover to the right or left as it
snaps into the valve opening.
3. Remove AC plug, cord, and One Touch® Comfort Control Wand from plastic bag and shrink wrap.
4. Plug into any standard polarized 110 Volt AC electrical outlet. North American Electrical rating:
120 VAC 60HZ 1.0A (Note: 230VAC product sold outside of North America.)
This product has a polarized attachment plug (one blade is wider than the other) as a safety feature.
This plug will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless
the plug can be fully inserted. Do not attempt to defeat this safety feature.
5. Push and hold inflation/firmer button on the One Touch® Comfort Control Wand for
approximately 3 minutes to inflate your AeroBed Raised to the full (firmest) capacity. Bed will not over-inflate.
6. Lie on the bed and use Comfort Control Wand to adjust the firmness to your desired level. For firmer
bed, press inflate/firmer button. For softer bed, press deflate/softer button.
CAUTION: Do not sleep on edges of the bed. Edges are less supportive and may crush under weight.
DEFLATION AND STORAGE
1. Make sure the bed is unplugged from the electrical outlet prior to deflation.
2. To deflate your AeroBed Raised, open the Quick Air Release Valve at the foot of the bed. Deflation takes approximately 1 minute.
3. Roll or fold the AC cord with wand control and secure it. Fold sides of bed into the center along
its length. Tightly roll your AeroBed Raised around the pump towards the air release end.
When the bed is completely rolled, push the Air Release Valve closed until it locks.
4.Store your AeroBed Raised in a clean, dry place at room temperature (above 50°F/10ºC). Storing your
AeroBed under 50ºF (10ºC) and over 100ºF (38ºC) may affect its performance and will not be covered under warranty.
NOTE: Bed must be at room temperature prior to inflating or it may cause air leaks.
CARE AND MAINTENANCE
1. Inspect your AeroBed Raised prior to each use.
2. Keep your AeroBed Raised away from any sharp objects. Large cuts or snags may not be repairable and will
not be covered by your warranty.
3. When not in use, store your AeroBed Raised in a clean, dry place out of extreme temperatures.
Product must be at room temperature prior to inflating.
4. In case of incidental damage to your bed, a repair patch has been included. Please follow repair instructions carefully.
Premier Raised Instruction Manual
7917 Rev. 01/07 111DV
This is the closed position. Open Air Release Valve Close Valve Using 2 Thumbs