Sony XDP-PK1000 - Manual (Page 21)

21
Specifications
DSP Master Unit
AUDIO POWER SPECIFICATIONS
CEA2006 Standard
Power Output: 17 Watts RMS 4 at
4 Ohms < 1% THD+N
SN Ratio: 80 dBA
(reference: 1 Watt into 4 Ohms)
Power-AMP
Output: Speaker outputs 4 CH
(Front L/R, Rear L/R)
Speaker impedance:
4 Ω – 8 Ω
Maximum power output: 45 W × 4 (at 4 Ω)
General
Outputs:
Audio output terminals: (Front/Rear)
Subwoofer output terminal (mono)
Power amplifier control terminal
Inputs:
iPod signal input terminal (dock connector)
Hi-level input terminal
Sound controls:
Bass/Treble ±7 dB
Fader/Balance ±7 steps
SUB-W Volume +/- 6Step , No sound
Power requirements: 12 V DC car battery
(negative ground (earth))
Dimensions: (Mounting dimensions)
Approx. 210.6 mm × 40 mm × 156.6 mm
(8
3 /
8
in × 1 5 /
8
in × 6 1 /
4
in) (w/h/d)
Mass: Approx. 0.92 kg (2 lb 1 oz)
Supplied accessories:
Card remote commander: RM-X251
Parts for installation and connections (1set)
Cradle
Dimensions: (Mounting dimensions)
Approx. 65 mm × 138.8* mm × 107.8 mm
(2
5 /
8
in × 5 1 /
2
in × 4 1 /
4
in) (w/h/d)
Mass: Approx. 0.14 kg (5 oz)
* Arm fully extended: 147.1 mm (5 7
/ 8 in ) (h)
Amplifier
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
AUDIO POWER SPECIFICATIONS
CEA2006 Standard
Power Output: 300 Watts RMS 4 at
4 Ohms < 1% THD+N
SN Ratio: 65 dBA
(reference: 1 Watt into 4 Ohms)
330 watts minimum continuous average
power into 4 ohms, 20 Hz to 100 Hz with no
more than 1.0% total harmonic distortion per
Car Audio Ad Hoc Committee standards.
Other Specifications
Circuit system:
Class D Technology
Pulse power supply
Input:
RCA pin jacks
Outputs:
Speaker terminals
Through out pin jacks
Suitable speaker impedance: 4 Ω – 8 Ω
Maximum outputs: 600 W (at 4 Ω)
Rated outputs (supply voltage at 14.4 V): 300 W
RMS (20 Hz – 100 Hz, 1.0 % THD + N, at 4 Ω)
SN Ratio: 65 dBA (Reference 1 W into 4 Ω)
Frequency response: 10 Hz – 120 Hz ( dB)
Harmonic distortion: 0.1 % or less (at 50 Hz, 4 Ω)
Input level: 1.0 V (RCA pin jacks)
Subsonic filter: 6 Hz, 12 dB/oct
Low pass filter: 120 Hz, 12 dB/oct
Power requirements: 12 V DC car battery
(negative ground)
Power supply voltage: 10.5 V – 16 V
Current drain:
at rated output: 25 A (at 4 Ω)
Remote input: 1 mA
Dimensions: Approx. 356.8 mm × 55 mm ×
276.8 mm (14 1 / 8 in × 2 1 / 4 in × 11 in) (w/h/d)
not incl. projecting parts and controls
Mass: Approx. 2.9 kg (6 lb 7 oz) not incl. accessories
Supplied accessories: Parts for installation
Subwoofer
Speaker: 30 cm (12 in), cone type woofer
Enclosure: Shielded type
Short-term Maximum Power * 1 : 1,000 W* 2
Rated power: 300 W* 2
CEA2031, RMS Power: 420 W
Rated impedance: 4 Ω
Output sound pressure level: 86 ± 2 dB (1 W, 1 m)* 2
+0
-3