Amm12n tuner operation – Advent AMM12N User Manual
Page 25
21
AMM12N
TUNER OPERATION
Tuner TFT Display
1.
Current radio band indicator
2.
Radio frequency indicator
3.
Clock
4.
Stereo broadcasting indicator
5.
Strong Local signal broadcasting indicator
6.
Preset radio stations: Touch to recall preset stations
7.
RDS Information: PS (Program Service), PTY (Program
Type), RT (Radio Text)
8.
EQ: Touch to view Spectrum Analyzer > Equalizer
9.
Touch to access the direct entry screen
10. Current preset station indicator
11.
|<<: Touch to seek backward
12. >>|: Touch to seek forward
13.
: Touch to tune backward one step
14.
: Touch to tune forward one step
15. BAND: Touch to change between AM/FM bands
16. AS: Touch to automatically store stations
17. Touch to view the SOURCE MENU and select a new
playback source
18. MEM: View screen used to enter current channel into
preset memory
19. 1/2 or 2/2: Touch this page button to view a second page
of on-screen buttons
20. Touch to view the SETUP menu
21. PS (Preview Scan): Touch to scan all stations available,
stopping for 5 seconds at each and continuing until a
station is selected
22. LOC: Touch to tune to strong local stations
23. PTY: When PTY is pressed, the Program Type
categories are listed, allowing listeners to find similar
programming by genre. When a PTY category is
selected from the touch screen menu, the radio will start
scanning for the selected category.
24. Indicates the PTY function is activated
25. Indicates the RDS function is activated
26. REAR: Touch to view the Rear source screen
27. PIP: Touch to view Rear, Front or NAV source
Switch to Radio Tuner source
•
Touch the top left corner of the screen (the RADIO
circle) to view the SOURCE MENU. Touch “RADIO”.
•
Press the SRC button (6) on the front panel or remote
control (8) to switch to the AM/FM or RADIO source.
Select FM/AM Band
Touch the BAND button (15) on the screen, or press the
BAND button on the unit (4) or remote control (20) to change
between the following bands: FM1, FM2, FM3, AM1, and
AM2.
NOTE: The BAND button on the unit only works when the
TFT is closed.
Seek Tuning
To seek the next higher station:
•
Touch the >>| button on screen.
•
Move the joystick to the right.
To seek the next lower station:
•
Touch the |<<| button on screen.
•
Move the joystick to the left.
Manual Tuning
To increase or decrease the tuning frequency one step:
•
Touch the or buttons on screen.
•
Move the joystick left/right.
Direct Tuning
To enter a radio station directly, touch the
button or
press the GOTO button (21) on the remote control to display
the direct entry menu.
Enter the desired radio station using the on-screen number
pad. Press Enter to tune to the selected station. To exit the
screen without changing the station, touch Exit. To clear your
entry and start over, touch Clear.
Using Preset Stations
Six numbered preset buttons store and recall stations for
each band. All six stored stations (P1-P6) for the current
band appear on the screen.
Storing a Station
1.
Select a band (if needed), then select a station.
2.
Touch the on-screen MEM button (18), on page 2/2 of
the onscreen options, to open the preset screen.
3.
Touch the preset number in which you would like to
store the current station (or press EXIT to cancel and
3
PS:
7
6
01:53 PM
E
Q
R
E
A
R
P
I
P
RADIO
1
4
8
10
2
5
17
26
FM-1
P1
87.5 MHz
ST
LOC
PTY
RDS
24
25
28
AS
BAND
1/2
PS
P1
87.5 MHz
P2
90.1 MHz
P3
98.1 MHz
P4
106.1 MHz
P5
107.9 MHz
P6
102.9 MHz
27
AS
PTY
BAND
1/2
PS
9
11
12
13
14
15
16
MEM
19
18
20
21
23
2/2
LOC
22
FM: _ _ _ . _ MHz
1
2
3
4
5
6
7
8
9
0
Clear
Exit
Mem: _
E x i t
P1 P2
P3
P4 P5 P6