intimus 3000 C - Manual (Page 5)

MATERIAL JAM IN MACHINE:
(Auto-reverse-function)
If too much material is fed in, causing a jam, the
machine will respond as follows:
- Cutting mechanism halts, then runs one step in
reverse (material will be released) and stops.
- The motor shuts down automatically.
- The pilot lamp (5) (fig. 1) lights up.
Proceed as follows:
Paper jam in the paper feed slot (9)
- Tear off the returned paper just above the feed
slot.
- Briefly move the rocker switch (1) (fig. 1) to the
“ ” position.
- The pilot lamp (5) (fig. 1) goes out.
- The cutting system then runs forward and shreds
the paper remaining in the cutter.
- Continue shredding, feeding smaller quantities
of paper.
Material jam in the CD/DVD feed slot (10)
- Remove the returned material.
Take care when removing material as
sharp edges may cause injury!
- Briefly move the rocker switch (1) (fig. 1) to the
“ ” position.
- The pilot lamp (5) (fig. 1) goes out.
- The remaining material to be shredded is then
fed to the cutting system again.
- Once the remaining material has been shred-
ded, continue shredding, feeding the correct
quantities.
- If necessary, move the cutting system manually
to and fro between forward and reverse running
until all the material has been fed through and
shredded.
Wait each time until the motor stops
before switching direction!
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. The pilot lamp (6) (fig. 1)
lights up. Turn the machine off with the pushbutton
switch (1) (fig. 1).
Allow the motor to cool down for 50 to 55 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the follo-
wing:
- Is the plug connected to the mains?
- Is the pushbutton switch (1) on?
- is the receptacle placed properly under the
machine?
- is the receptacle full?
The receptacle has to be emptied.
- is there a material jam in the machine?
Follow the instructions under ”MATERIAL
JAM”
- has the motor been overloaded?
Wait until the motor has cooled, and then re-
start.
If none of the above applies, please contact
your dealer.
3
93404 1 08/13
11
3,8x48
mm
4 mm
3000S 3000C
MAINTANENCE OF THE
CUTTING MECHANISM (3,8x48 mm):
Cross-cut cutting mechanism should be
oiled regular after a certain operating time
to maintain the cutting performance.
This can be easily accomplished if you
pour special shredder oil (Order-No. see
ACCESSORIES) as shown on a sheet of
paper and feed it through the inlet guide
to the cutting mechanism (fig. 5).
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched off
over night (pushbutton switch (1) (fig. 1).
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the
end of its useful service life. Do not
dispose of any of the parts included
in the machine or its packaging with
household trash.
OPERATION MAINTENANCE / DISPOSING
CLEANING THE PHOTOCELLS (fig. 4):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is pos-
sible that the machine will not turn off, due to the
broken light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes“ of the photocell with a brush.
TECHNICAL DATA
MALFUNCTIONS
ACCESSORIES
Cutting width:
3000S: 4 mm
3000C: 3.8x48 mm
Cutting capacity paper:
3000S: 20-22 sheets (70g/m 2 )
3000C: 13-16 sheets (70g/m 2 )
Cutting capacity
Credit cards/CD’s/DVD’s: feed one at a time
Supply voltage: 230V/50Hz
240V/50Hz
120V/60Hz
Pre-fusing: 10 amps (slow-blow)
Noise level: approx. 62 dB(A)
Power: 0.37 kW
Intermittent operation: 5 min ON
55 min OFF
Dimensions:
Width: 420 mm
Depth: 340 mm
Height: 660 mm
Weight: ca. 15kg
GB
Description Order-No.
Plastic bag, 300 x 300 x 700 x 0,018 mm 99925
Lubricant, 110 ml bottle 88035
Note: For orders of special accessories and spare parts, please contact your dealer.
EMPTYING THE RECEPTACLE (Fig. 3):
Proceed as follows:
- Remove the receptacle from in front of the ma-
chine and empty its contents. Pilot lamp lights
up (7) (fig. 1).
- Replace the empty receptacle under the machine
and push all the way to the back.
Note: The machine will only run when the recepta-
cle is pushed completely under the machine.
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
5
fig. 5
fig. 4 fig. 3