Astro Pneumatic 557010 Adjustable Extra Heavy Duty Portable Work Stand - Manual

Page 2
557010
ADJUSTABLE EXTRA HEAVY DUTY
PORTABLE WORK STAND
ADJUSTABLE EXTRA HEAVY DUTY
PORTABLE WORK STAND
Important
When unpacking, check the parts diagram and part number
listing on page 2 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
Unpacking
www.astrotools.com
Astro Pneumatic Tool Co. warrants our products to the original user against defective
material or workmanship for a period of 1 year from the date of 1st use. Astro reserves
the right to determine whether the product failed because of defective material,
workmanship or other causes and to charge back for missing parts. Astro Pneumatic
Tool Co., at its discretion, will repair products covered under this warranty free of
charge. The original user is to return the product (with the exceptions listed below) with
the distributor’s name, address, adequate proof of date of purchase or a copy of
warranty card, and a short note explaining the problem. Failures caused by accident,
alteration, or misuse are not covered by this warranty.
Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and
may not be transferred to subsequent owners.
This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do not
allow the exclusion of limitations of incidental or consequential damages so the above
limitations may not apply to you.
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS.
Product Information
Assembly Instruction
•
•
•
•
•
Normal use of this product is likely to expose
the user to dust and/or microscopic particles
containing chemicals known to the State of
California to cause cancer, birth defects
or other reproductive harm. Always wear
appropriate safety equipment and clothing when
using this product. Study, understand and follow
all instructions provided with this product.
Always wear ANSI approved goggles when using
this product.
Always select the correct accessories of the
correct size and design for the job that you are
attempting to perform.
Always work in a clean, safe, well-lit, organized
and adequately equipped area.
Do not begin repairs without assurance that
vehicle is in secure position, and will not move
during repair.
• Heavy Duty work bench with capacity of 500lbs.
• Heavier gauge tubing (31.74mm)
• 1-1/4" Steel tubing construction with 1/2"
foam padded top
• Great for working on doors, fenders, hoods
and bumpers
• Adjustable height of 25" to 41" tall
• Stand Dimensions in Completely Folded
Position: 40" wide x 42" high
• Stand Dimensions in Adjustable Operating Position:
Maximum Height: 14" depth x 41" high x 40" wide
Minimum Height: 32" depth x 25" high x 40" wide
• Tubing diameter is 1-1/4" (32mm)
• Weight: 16lbs.
Product: 557010 Manual
Dimension: 8.5"x 11"/page
Date: 2008/09/30
Color: Black
557010
372 Old US Highway 52 South
Mount Airy, NC 27030
Call 1.800.221.9705 for questions concerning performance of the product
or other inquiries.
Metal edges can be sharp, please use extreme caution during assembly.
1. Attach rubber end caps (#2) to four leg tubes (#8).
2. Slide foam pad (#1) onto both outer top frame tube (#9) and inner top frame tube (#10).
Then, slide leg tubes (#8) into both frame tubes. Match up holes.
3. Add a flat washer (#7) to eye bolt (# 3). Do not disturb fixed nuts on both eye bolts and eye hook assemblies. And, push eye bolt (# 3) thru holes of
leg tube (#8) and outer top frame tube (#9) assembly (see Figure A). Assemble so that the eye bolt (# 3) is on the inside of the work bench. Add a second
flat washer (#7) and lock nut (#6) and tighten snugly. Repeat the same steps for the second set of legs. When complete and the work bench is assembled,
the eye bolts (#3) will be on the opposite sides facing inwards.
4. Slide leg tubes (#8) into inner top frame tube (#10). Twist legs until the holes are aligned. Assemble eye hook assemblies (#4) duplicating the same
assembly process as in step #3, all eye bolts and eye hook assemblies are facing inward when complete. When the work bench is assembled, the chains
with eye bolts and eye hook assemblies will be on opposite sides facing inwards.
5. Set up both parts of the stand so that the eye bolts with chains (#3) and eye hook assemblies (#4) are on opposite sides facing inside of work bench.
Attach eye bolts chains to eye hook assemblies on the opposite sides of the work bench. Attach both halves (#8)
together with a bolt (#11) a flat washer (#14) and a special washer (#12) inserted between both legs
(see Figure B). And finally put a third flat washer (#14) before adding lock nut (#13) onto the bolt.
6. Last, tighten all fasteners when completely assembled. Do not over tighten as the tubing can crush.
Please make sure the chain and hook assemblies on both
sides of the stand are adjusted to equal lengths. See Figure C.
Figure C
MADE IN CHINA
1 2 6 7
8 9 10 11
3 4
Fig. A
3 6 7 7
Fig. B
Fig. A
1
2
10
8
4
9
Fig. B
11 12
14 14
13
557010-A01
557010-A02
557010-A03
557010-A04
557010-A06
557010-A07
557010-A08 Foam Pad
Rubber Cover
Chain with Eye Bolt- 10.5"
Eye Hook Assembly
Lock Nut M8
Washer M8x16mm
Leg Tube 2
4
2
2
4
8
4 1
2
3
4
6
7
8
Index
No.
557010-A09
557010-A10
557010-A11
557010-A12
557010-A13
557010-A14 Outer Top Frame Tube
Inner Top Frame Tube
Bolt M10 x 75mm
Washer M10 x 30 x 3mm
M10 Lock Nut
Washer M10 x 20 x 1mm 1
1
2
2
2
4 9
10
11
12
13
14
Index
No.
ADJUSTABLE EXTRA HEAVY DUTY
PORTABLE WORK STAND
12 13 14