Apm 52 00, 20” industrial pa nel mount lcd – Acnodes APM 5200 User Manual
Page 2
14628 Central Ave,
Chino, CA 91710
tel:909.597.7588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product descr
are subject to change without no,
please visit Acnodes’ web site at
APM 52
20” Industrial Pa
Legal Information
First English printing, O ctober 2002
Information in this doc ument has been carefully checked for accuracy; however, no guarantee is g
of the contents. The information in this docum ent is subject to change without notice. W e are not li
loss that results from the use of this equipm ent.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual f
¦ Unplug equipm ent before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
¦ Keep equipm ent away from excessive humidity and heat. Preferably, keep it in an air-condition
temperatures not exceeding 40º Celsius (104º Fahrenheit).
¦ When installing, place the equipment on a sturdy, level surface to prevent it from accidentally fa
age to other equipment or injury to persons nearby.
¦ When the equipment is in an open position, do not cover, block or in any way obstruct the gap b
power supply. Proper air convection is necessary to k eep it from overheating.
¦ Arrange the equipm ent’s power cord in such a way that others won’t trip or fall over it.
¦ If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the v
labeled on the equipment’s electric al ratings label. The voltage rating on the cord should be hi
on the equipment’s ratings label.
¦ Observ e all precautions and warnings attached to the equipment.
¦ If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to
aged by transient over-voltage.
¦ Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spill
supply or on other hardware may cause damage, fire or electrical shock.
¦ Only qualified service personnel should open the chassis. O pening it yourself could damage th
date its warranty.
¦ If any part of the equipment becomes damaged or stops functioning, have it c hecked by qualifie
W hat the w arranty does not cover
¦ Any product, on which the serial number has been defaced, modified or rem oved.
¦ Damage, deterioration or malfunction resulting from:
? Accident, m isuse, neglect, fire, water, lightning, or other acts of nature, unauthorized produc
failure to follow instructions supplied with the product.
? Repair or attempted repair by anyone not authorized by us.
? Any damage of the product due to shipment.
? Removal or ins tallation of the product.
? Causes external to the product, such as electric power fluctuation or failure.
? Use of supplies or parts not meeting our specifications.
? Normal wear and tear.
? Any other causes which does not relate to a product defect.
¦ Removal, installation, and s et-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, p
FCC rules. These limits are designed to provide reasonable protection against harmful interferenc
lation.
Any changes or modifications made to this equipment may void the user’s authority to operate this
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
instructions, m ay cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this e
harmful interference to radio or televis ion reception, which c an be determined by turning the equi
user is encouraged to try to correct the interference by one or more of the following m easures:
¦ Re-pos ition or relocate the receiving antenna.
¦ Increase the separation between the equipm ent and receiver.
¦ Connect the equipment into an outlet on a circuit different from that to which the receiver is con