Yamaha NS-FP9500 User Manual
Quick-connect guide, Room layout, Main speaker assembly in the box
2
Room Layout
Speaker Placement After assembly of the speakers place them so they appear in the approximate positions as
shown in the diagram above.
Quick-Connect Guide
NS-FP9500
Home Cinema Speaker Package
���
���
���� �������
1
3
6
5
8
Connect Main Speaker Wire For
illustration purposes, stand, which is now
attached to speaker, is not shown in diagram
above. Locate screw-type input terminals
at the rear of each of the speakers. Connect
the speaker wire as shown. The positive
(+) side of the wire with the white stripe
attaches to the red terminal. The negative
(-) side attaches to the black terminal.
(Please see your NS-FP9500 Owner’s Manual
for more detailed instructions on speaker
wire connections.) Place assembled main
speakers in desired location to the left and
right of the viewing/audio source. (See Step
2, Room Layout.)
Attach Bases to Stands Apply the non-skid pads
as shown in the
inset. Identify both speaker stands
and both bases
and attach using
short screws
as shown.
Attach Finishing Brackets
on top of two speaker stands.
Inspect Contents After unpacking, inspect the contents to confirm you have the above items:
two main
speakers,
three rear speakers,
one center speaker,
speaker wire,
two bases,
two speaker stands,
two finishing brackets,
RCA cable, one bag each of
long screws (8) and
short screws (4),
center speaker
bracket and screw,
subwoofer,
non-skid pads for base,
non-skid pads for stands, and
cable protection seal
for base.
9
Attach Bracket and Speaker Wire Attach bracket
to center
speaker
using supplied screw as shown. Attach speaker wire as shown
in Step 6.
Main Speaker Assembly
In the Box
NOTE
Banana plug connectors (not
included) can be used to connect speaker
wire to speaker terminals. Please see your
Owner’s Manual for directions.
Front Center Speaker Assembly
Yamaha created this package to greatly enhance your audio and home theater enjoyment. This Quick-Connect
Guide will help you get started. Follow the steps to assemble and connect the speakers first. Refer to your
Owner’s Manuals as well as those that came with your other components for complete instructions and
precautions. Be sure to turn off all power while making connections. You will need the following which are not
included in the package: Phillips screwdriver, wire cutter/stripper, brackets, toggle bolts, molly anchor screws
or sheet metal screws.
(8)
(2)
(4)
Thread Speaker
Wires Cut
speaker wire
to
appropriate lengths
for all speaker
connections and
set aside. Place
each long stand
upright on its base.
Thread main speaker
wire through
oval opening on
stand and pull
through opening
on underside of
base. Pull wire all
the way through
leaving extra length
near oval opening
as shown. Apply
non-skid pads
on
stands.
4
Speaker
Wire
Attach Main
Speakers Lay stands
down. Line up holes
so that oval opening
is near speaker wire
connections on speaker.
Attach main speakers
using long screws as
shown. Attach cable
protection seal
to
base as shown in inset.
Mount Rear Speakers and Rear Center Speaker (Optional) Fasten mounting screws into
a firm wall or wall support as shown. Hang the keyholes on the back of the each of the speakers
on
the protruding screws. Attach speaker wire as shown in Step 6.
For mounting
screws, use
minimum
1
3
/
4
"
tapping
screw (not
included).
Leave
1
/
4
"
space
between screw
head and wall.
16
7/32"
16
7/32"
TYPICAL
WARNING
If you are unsure of how to securely and safely fasten speakers to a wall, please contact a
reliable source about the best type of hardware for your particular wall’s construction. Secure installation
is the purchaser’s responsibility. See Owner’s Manual for additional instructions and precautions.
7
Rear
Speakers
1
3/4"
use this size screw
use this size screw