Yamaha GX-500VCD - Manual (Page 17)

E-9
English
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
TIME PROG R. TIME
C
EDIT +10
D
PRESET
E
MODE REPEAT RANDOM TUNER
SELECT RETURN TIME INDEX
DISC SKIP
DIRECTION DIGEST KARAOKE INTRO
KEY/ECHO YMERSION BASS BOOST MUSIC
POWER SLEEP
INPUT VOLUME
A B
TAPE
TUNER
VCD / CD
LEVEL
/I
REC/PAUSE
DISC 1 DISC 2 DISC 3
3–DISC VCD CHANGER
STANDBY TIMER
DOWN UP
VOLUME
STANDBY/ON
AUTO REVERSE CASSETTE DECK DOLBY B NR
DIRECTION
YMERSION B.BOOST MUSIC INPUT INPUT
PHONES
MIN
PRESET/ TUNING/ BAND A/B/C/D/E
DISC CHANGE OPEN / CLOSE
TREBLE BASS
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSE DOLBY NR
HOUR
RANDOM REPEAT TIME
DISPLAY MODE
MIC MIXING KARAOKE
MIN MAX
1 MIC 2
Basic play
*
When you play a Video CD, turn on the TV monitor
connected to this system.
1
Turn on the power.
2
Select the CD/Video CD player by pressing INPUT or
until “VCD/CD” (
2
) appears on the display.
3
Press OPEN/CLOSE to open the disc tray.
4
Place discs on the table, label side upward.
* Up to three discs can be loaded on the table.
To load the third disc, rotate the disc table by pressing
DISC CHANGE on the front panel.
* 8 cm (3”) discs can be played without an adaptor.
* The disc placed on the left side is played first.
5
Press OPEN/CLOSE to close the disc tray.
* If the selected disc is a CD, the total number of tracks
(
1
) and the total playing time of the disc (
2
) will be
displayed for several seconds.
* If the disc contains more than 15 tracks, the “OVER 15”
indicator (
0
) will light up.
* If the disc tray is closed by pushing the front edge of the
tray, play will begin automatically.
*
If the selected disc is a Video CD, “VCD” (
4
) lights up
on the display.
6
Press / to begin play.
If a Video CD (version 2.0) is selected, “PBC” (
5
) lights up on
the display, yet the total number of tracks (
1
), the total
playing time of the disc (
2
) and the music calendar (
9
) will
not be displayed. In this mode, disc play is controlled by the
rule of Playback Control. To play the disc in the Playback
Control mode, skip to page 16 and follow the procedure.
To cancel this mode and restore the normal play mode, press
. “PBC” (
5
) disappears from the display.
To call the Playback Control mode again, press SELECT on
the remote control.
To pause
1 1
Press / .
* The “ ” indicator (
7
) will flash.
2 2
Press / to resume play from the same point.
To stop play
Press .
To finish using this system
Turn this system into the standby mode by pressing
STANDBY/ON. (The STANDBY indicator will light up and the
display will go out.)
3, 5
CD/Video CD player operation
2
1
2
4
1
6, 1 1 , 2 2
4
STANDBY indicator
6, 1 1 , 2 2
Direct operation
DISC (1, 2 or 3) and OPEN/CLOSE on the front panel and
on the remote control will work if they are pressed when
this system is in the standby mode or another input source is
selected.
SELECT
For Video CDs
For Video CDs
Note for Video CDs