PAC J1850 - Manual (Page 2)

Pacific Accessory Corporation - Santa Ana, CA 92705
[email protected] • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
07-07-09
J1850 Class 2 VPW
Class 2 J1850
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0 1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Arbitration EOD CRC
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0 1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Class 2 Class 2 J1850
Installing the BLU-GM29 with the Parrot CK3000: If you are installing the BLU-
GM29 into a vehicle that is not equipped with factory steering wheel controls, the
controller that came with the Parrot MUST be used. Please see the section below
on “All Other Bluetooth Kits” for hard-wiring information. Otherwise, plug the 12-
pin connector on the supplied PARROT2SPLIT harness into the 12-pin receptacle on
the SPLITGM29 harness. Plug the free ends of the PARROT2SPLIT harness into the
Parrot CK3000 control box. This must be done BEFORE the SPLITGM29 harness is
connected to the vehicle.
Controlling the Parrot CK3000 with the BLU-GM29:
To turn Bluetooth controls on or off, press and hold the Source button on the steering
wheel. After one second you will hear either one or two confirmation chimes. You MUST
release the button as soon as you hear the chime. If you do not release the button
within one second after the chime is heard the button will revert to it’s factory function
of changing the source. One chime indicates that the Bluetooth controls are on; two
chimes indicates that the Bluetooth controls are off.
When the Bluetooth controls are activated, the driver information center will display
“BT Control ON”. Whenever a call is incoming or active, the steering wheel controls
automatically switch to Bluetooth control. If you would like to access the features menu
of the Parrot CK3000 you MUST activate Bluetooth controls before this can be done.
When the Bluetooth controls are de-activated or a call is ended, the driver information
center will display “BT Control Off”. Once a call is ended the steering wheel controls
automatically switch back to their factory functions.
Volume Control/Level Matching:
It is very important that you match the volume level of the Parrot kit to the radio.
When you first install the Parrot kit with the BLU-GM29 the volume may be very
loud and distorted. While in the “BT Control On” mode, the volume controls on the
steering wheel will act exactly like the rotary knob on the Parrot control unit. This allows
you to scroll through the Parrot menus and access the volume setting along with other
features. To match the volume levels, press and hold the Source button on the steering
wheel until a beep is heard. Press the “Play/Pause” button on the steering wheel, you
should hear the Parrot kit’s menu prompt. Use the volume controls on the steering
wheel to scroll through the choices until the Parrot kit says “Volume”. Press the “Play/
Pause” button on the steering wheel to select volume adjustment. You can now adjust
the volumes and match them to an acceptable level (the radio volume must be adjusted
by the volume knob on the radio).Once the volume level of the Parrot kit is set you
should not have to change it again as all other volume control can be done though the
radio or the phone itself.
SRCE
Menu
End Call
Answer Call/
Privacy Mode
Press & hold to
enable/disable
Bluetooth controls
Rotary Knob
Clockwise
Rotary Knob
Counter-Clockwise
Phone Controls
BLU-GM29
GM LAN 29bit Universal
Bluetooth Integration Interface
To Vehicle To Factory Radio
PARROT2SPLIT
Harness
To Parrot CK3000
SPLIT
GM29 Har
ness
Connection Diagram
Installing the BLU-GM29 with the Motorola IHF1000/1700: Plug the 12-pin connector on the supplied MOTO2SPLIT harness into the
12-pin receptacle on the SPLITGM29 harness. Plug the free ends of the MOTO2SPLIT
harness into the Motorola IHF1000/1700 control box. This must be done BEFORE the
SPLITGM29 harness is connected to the vehicle.
Controlling the Motorola IHF1000/1700 with the BLU-GM29:
To turn Bluetooth controls on or off, press and hold the Source button on the steering
wheel. After one second you will hear either one or two confirmation chimes. You MUST
release the button as soon as you hear the chime. If you do not release the button
within one second after the chime is heard the button will revert to it’s factory function of
changing the source. One chime indicates that the Bluetooth controls are on; two chimes
indicates that the Bluetooth controls are off.
When the Bluetooth controls are activated, the driver information center will display
“BT Control ON”. Whenever a call is incoming or active, the steering wheel controls
automatically switch to Bluetooth control. If you would like to access the features menu
of the Motorola IHF1000/1700 you MUST activate Bluetooth controls before this can be
done.
When the Bluetooth controls are de-activated or a call is ended, the driver information center will display “BT Control Off”. Once a call is
ended the steering wheel controls automatically switch back to their factory functions.
BLU-GM29
GM LAN 29bit Universal
Bluetooth Integration Interface
To Vehicle To Factory Radio
MOTO2SPLIT
Harness
To Motorola
IHF1000/1700
SPLIT
GM29 Har
ness
Connection Diagram
Parrot CK3000
Motorola IHF1000/1700
Page 2