Klipsch CDT ARCHITECTURAL - Manual (Page 3)

4. Insert the speaker assembly into the opening and attach by
tightening the four Phillips screws (below). The frame’s four
“dogs” will swivel out and “sandwich” the wall and frame togeth-
er as they are tightened. If you use a power tool to tighten these
screws, please use a low torque setting. Failure to do so could
result in damage to your speaker.
5. Adjust the direction of the speaker by swiveling it to the
left or right as needed. If desired, you may also adjust the tilt
of the speaker and gently adjust the horn to the desired angle.
Do not attempt to turn the tweeter stem while adjusting the
swivel tweeter.
6. At this point, you may paint the speaker grilles before attach-
ing them to the speaker. Klipsch grilles are designed to accept
most types of paint. Care should be taken to avoid excessive
paint build-up in the grille perforations.
7. Press the grille into place.
See back page for more illustrations.
OPERATING CONTROLS
Mid-Bass and Tweeter Attenuator Switch
(3000 and 5000 Series)
Some CDT models feature a Tweeter switch (3000 series) or
both a Mid-Bass and a Tweeter switch (3000 & 5000 series)
located on the front baffle. The switch allows a setting of either
0dB (normal) or –3dB in the respective frequency range. If
installing in an acoustically bright room, such as a bathroom or
kitchen, you may want to adjust the Tweeter level switch. If the
speaker is located in a corner and produces too much bass, you
may need to adjust the Mid-Bass level switch. The position
of the switches should always be checked prior to attaching
the grille.
LIMITED LIFETIME WARRANTY FOR KLIPSCH-BRANDED
IN-WALL, INCEILING AND OUTDOOR SPEAKERS
Klipsch warrants to the original retail purchaser that this product
is to be free from defective materials and workmanship for the
life of the product, if it is properly used and maintained. If this
product proves defective in either material or workmanship,
Klipsch, at its option, will (a) repair the product, or (b) replace the
product, at no charge for parts or labor. If the product model is
no longer available and cannot be repaired effectively or replaced
with an identical model, Klipsch at its sole option may replace
the unit with a current model of equal or greater value. In some
cases, modification to the mounting surface may be required
where a new model is substituted. Klipsch assumes no responsi-
bility or liability for such modification. To obtain a repair or
replacement under the terms of this warranty, please contact our
customer service group at 1-800-KLIPSCH. You will be required
to submit a copy of the original receipt via fax or email. The
receipt must reflect that you are the original purchaser, the prod-
uct was bought from an authorized Klipsch retailer, and the prod-
uct is still within warranty. You will be issued a return authoriza-
tion number (RA#) and asked to ship the defective product,
together with proof of purchase and RA#, prepaid insured to the
address set forth Klipsch 137 Heampstead #278 Hope, AR
71801. Freight collect shipments will be refused. Risk of loss or
damage in transit is to be borne by the purchaser. Once Klipsch
receives the defective product, a repair or replacement order will
be initiated.
Limitations:
• This limited warranty does not cover failure of the product
resulting from improper installation, misuse, abuse, acci-
dent, neglect, mishandling, or wear from ordinary use or
environmental deterioration.
• This limited warranty does not cover cosmetic damage,
including paint damage, or consequential damage to other
components or premises which may result for any reason
from the failure of the product.
• This limited warranty is null and void for products not used
in accordance with Klipsch’s instructions.
• This limited warranty is null and void for products with
altered or missing serial numbers and for products not pur-
chased from an authorized dealer.
• This limited warranty terminates if you sell or otherwise
transfer this product to another party.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO
STATE, JURISDICTION TO JURISDICTION OR COUNTRY TO COUN-
TRY. KLIPSCH’S RESPONSIBILITY FOR MALFUNCTIONS AND
DEFECTS IN HARDWARE IS LIMITED TO REPLACEMENT OR
REPAIR AS SET FORTH IN THIS WARRANTY STATEMENT. FOR
CANADIAN CUSTOMERS, KLIPSCH DISCLAIMS ALL OTHER WAR-
RANTIES AND CONDITIONS, EXPRESS OR IMPLIED, STATUTORY
OR OTHERWISE, FOR THE PRODUCT. FOR U.S. CUSTOMERS, ALL
EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE LIMITED IN TIME TO THE TERM OF THIS WARRANTY. SOME
STATES, JURISDICTIONS OR COUNTRIES DO NOT ALLOW THE
EXCLUSION OF CERTAIN IMPLIED WARRANTIES OR CONDITIONS,