beautypg.com

Smeg K600TL User Manual

Page 20

background image

5019 612 10060

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized
conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in
the table in relation to the water supply pressure and temperature, the load and the type of wash.
The data on the “Energy Label” refer to the programme “Cotton 60°C”.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the

water out.

1. Load the machine, close the drum doors and

check that they are properly locked.

2. Add detergents and additives into the dispenser

to no more then the “MAX” level mark, as
follows:

Programme with pre and main wash

Main wash programme without prewash

Fabric softeners and conditioners

Chlorine bleach

Stain remover agents

Anti-scale agents (if necessary)

3. Turn the programme selector knob to the

desired programme.

4. Turn the temperature selector knob to the

desired temperature.

Selecting or deselecting an option can be done
at any time during the programme. The option
will be applied as long as the corresponding
programme phase has not been executed yet.

“No Spin” button

Especially for delicate garments to avoid wear and
tear caused by the spin.

Note: with the “Cotton” and “Synthetics”
programmes a short spin cycle is provided in any case,
even if the exclusion has been selected, in order to
optimize rinsing results.

“Half Load” button

Can be used for small loads and lightly soiled
laundry.

Reduces the water consumption especially
during the rinses.

“Intensive Rinse” button

• The amount of water is increased to ensure a

more intensive rinse.

• This option is particularly suitable for areas with

very soft water or washing linen laundry for
people with skin allergies.

CONSUMPTION DATA

Programme

Temperature

Selector

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton

95

5.0

63*

1.80

2:05

Cotton

60

5.0

55

1.20

2:05

Cotton

40

5.0

55

0.55

2:05

Synthetic

60

2.0

56

0.80

1:30

Synthetic

40

2.0

56

0.40

1:30

Delicate

40

1.5

60

0.55

0:45

Wool

40

1.0

60

0.50

0:40

Silk

30

1.0

60

0.30

0:50

PREPARATION OF WASH CYCLE

SELECT THE DESIRED OPTION

“Rinse Hold” button

• The laundry remains in the last rinse water

without progressing to the final spin cycle to
avoid creasing and prevent colours from fading.

• This option is particularly recommended for the

“Synthetic” and “Delicate” programmes.

• This function is particularly useful if you want to

postpone spinning to a later time, or if you want
to drain only.

Note: the programme selector knob stops
on

.

Appliance in “Rinse Hold”:

• Press the “Rinse Hold” button again: the

programme will terminate automatically with
the selected spin cycle.

• If you do not wish to spin the clothes, press the

On/Off” button, turn the programme selector
knob to the “Drain” programme and press the
On/Off” button again.

Turn on the tap and press the “On/Off” button.
The indicator light of the “On/Off” button lights up.
Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where
it was interrupted.

• The programme selector knob is in the Stop

position.

1. Press the “On/Off” button to switch off the

machine.

2. Cancel the options.

3. Turn the tap off.

4. Wait for the lid to unlock (about 1 minute).

5.

Open the lid and the drum doors and unload
the machine.

1. Switch off the machine by pressing the

On/Off” button.

2. Select the new programme.

3.

Start programme by pressing the “On/Off
button again.

If, for any reason, you wish to interrupt the
programme for a certain time and continue it later:

1. Press the “On/Off” button.

2. After the desired pause, press again the

“On/Off” button.

1. Switch off the machine by pressing the

On/Off” button.

2. Set the programme selector to “Drain”.

3. Press the “On/Off” button again to start the

“Drain” programme.

PROGRAMME START

END OF WASH CYCLE

CHANGE THE PROGRAMME DURING THE
WASH CYCLE

PAUSE/INTERRUPT A PROGRAMME

CANCEL PROGRAMME