Ikelite SD630 User Manual
Page 3

6
CChheecckkiinngg CCoonnttrroollss
Once the housing has been closed push the controls back into
place Make sure they line up with the camera’s controls Pull
out on the housing’s Zoom Control and align with the camera’s
Zoom Lever then push the housing control back in to engage
with the camera’s Zoom lever
TTuurrnniinngg tthhee CCaam
meerraa O
Onn
To turn the camera ON use the housing ON/OFF control to
slide the Camera Lens Cover away from the lens To turn the
camera OFF pull out on the housing ON/OFF control and
rotate it past the raised part of the Lens Cover push down and
slide the Lens Cover toward the lens (Lens will retract into
camera body)
U
Ussiinngg tthhee RRiigghhtt AArrrroow
w//FFllaasshh aanndd M
Muullttii CCoonnttrrooll D
Diiaall
The housing’s control for the camera’s Right Arrow/Flash and
Multi Control Dial has a white dot that aligns with the housing
controls activation paw The control is used in two different ways
To activate the Right Arrow/Flash function place the white dot
over the camera control and push in and pull out on the housing
control
To rotate the camera’s Multi Control Dial place the white dot at
about an o’clock position rotate the housing control clockwise
to about the o’clock position Lift the housing control and
repeat this action until the desired setting is obtained
CCAAU
UTTIIO
ON
N::
U
Unnddeerrw
waatteerr tthhee w
whhiittee ddoott oonn tthhee ccoonnttrrooll sshhoouulldd bbee ppllaacceedd iinn tthhee
oo’’cclloocckk ppoossiittiioonn ssoo iitt ddooeess nnoott aaccttiivvaattee tthhee ccaam
meerraa’’ss AArrrroow
w//FFllaasshh
ccoonnttrrooll U
Unnddeerrw
waatteerr tthhee w
waatteerr pprreessssuurree w
wiillll ppuusshh tthhiiss ccoonnttrrooll iinn
IIff tthhee ccaam
meerraa’’ss RRiigghhtt AArrrroow
w//FFllaasshh ccoonnttrrooll iiss hheelldd iinn tthhee ddeepprreesssseedd
ppoossiittiioonn sseevveerraall ccaam
meerraa ffuunnccttiioonnss w
wiillll nnoott aaccttiivvaattee
7
LLuubbrriiccaannttss
Ikelite provides silicone lubricant with the housing We recommend
you use only Ikelite lubricant on Ikelite products as some other
brands may cause the o’ring to swell and not seal properly
Use only enough lubricant to lightly cover control shafts and
o’rings Wipe off any excess lubricant with a clean cloth
Lubricant is not a sealant it is used to reduce friction Excessive
lubricant can collect sand and dirt which may interfere with
proper sealing
CCAAU
UTTIIO
ON
N
N
Neevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann
ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk
U
Ussiinngg tthhee ZZoooom
m CCoonnttrrooll U
Unnddeerrw
waatteerr
When the housing’s Zoom control is activated underwater the
water pressure will not allow the camera’s Zoom lever to return
to the center position When the camera’s Zoom lever is held to
either side it will not allow the camera to take a picture YYoouu
m
muusstt rreettuurrnn tthhee ccaam
meerraa’’ss ZZoooom
m lleevveerr ttoo tthhee cceenntteerr ppoossiittiioonn aafftteerr
eeaacchh aaccttiivvaattiioonn
4
IInnssttaalllliinngg tthhee CCaam
meerraa
Remove the back
from the housing
The mounting tray
for the camera is
secured to the
housing back
Position the camera
on the tray and
secure it with the
mounting bolt
which threads into
the camera’s tripod
socket U
Ussee aa ccooiinn
oorr ffllaatt bbllaaddeedd
ssccrreew
wddrriivveerr ttoo ttiigghhtteenn tthhee m
moouunnttiinngg bboolltt ssoo tthhee ccaam
meerraa iiss ffllaatt
aaggaaiinnsstt tthhee ttrraayy
CCAAU
UTTIIO
ON
N::
Some camera tripod socket threads are plastic The mounting
tray bolt is metal Do not cross thread or over tighten as you
may damage the camera tripod socket threads
CAMERA / MOUNT
Lid
Hook
O' Ring
Mounting Bolt
Mounting
Tray
See Lens Cover Note below
N
NO
OTTEE:: TThhee ccaam
meerraa’’ss LLeennss CCoovveerr m
muusstt bbee iinn tthhee ooppeenn
ppoossiittiioonn bbeeffoorree cclloossiinngg tthhee hhoouussiinngg
Slide the camera’s Lens Cover open then slide it back towards the
lens until the camera’s lens retracts back into the camera body
Leave the Lens Cover in this position when installing the camera
into the housing In this position the housing ON/OFF control can
be used to turn the camera on and off
5
CClloossiinngg tthhee H
Hoouussiinngg
Place housing face down in your
lap or on flat surface
Check to see that there is an
o’ring on the housing back and
that it is clean and in its proper
location
Guide the back onto the housing
The o’ring should touch the
housing all the way around There
should be an even gap all the way
around between the housing and
the housing back
Lift the lid snaps so they are
extended and place the lid snap
into the hook on the housing
back
To close the housing push
down on the lid snaps until
they snap into place Lid
snaps on opposite sides of the
housing should be closed at the
same time Be sure they are down
far enough to engage the lock
D
Doouubbllee cchheecckk Once the housing is closed check the o’ring seal
Check the gap between the housing back and the housing it
should be even all the way around
Look through the clear plastic back at the o’ring You should see a
darkened area where the o’ring is compressed against the
housing back If you do not see an even black compression seal
all the way around the back open the lid snaps reseat the
housing back and close the lid snaps Visually check the seal again
o’ring
housing back
housing back
housing
housing
o’ring
even gap
all 4 sides