Ingersoll-Rand LM2350E-X - Manual (Page 2)

LM2350E-X PAGE 2 OF 4
PARTS LIST / LM2350E–XX
ITEM DESCRIPTION (Size in Inches) QTY PART NO. [MTL] ITEM DESCRIPTION (Size In Inches) QTY PART NO. [MTL]
1 Carriage Bolt (1/4" - 20 x 9" long) (4) 94333 [C]
2 Upper Cap (1) 94390 [Z]
n 3 Track Gasket (2) 94392 [B]
4 Sleeve (2) 94316 [Br]
n 5 ``O" Ring (1/16" x 11/16" o.d.) (4) Y325-15 [B]
n 6 ``O" Ring (1/8" x 3/4" o.d.) (4) Y325-206 [B]
7 Spool (2) 94310 [D]
n 8 ``U" Cup (1/8" x 3/4" o.d.) (2) Y240-7 [B]
n 9 ``O" Ring (.106" x .587" o.d.) (2) 15066 [B]
10 Cylinder (1) 94306 [A]
11 Adapter (1) 94384 [C]
n 13 ``O" Ring (1/16" x 7/16" o.d.) (1) Y325-11 [B]
14 Muffler Housing (1) 94443 [A]
15 Foam Liner (2) 94402
16 Edge Trim (2) 94378-1 [N]
18 Retaining Ring (1) 94406 [C]
19 Washer (1) 94515 [C]
n 20 ``U" Cup (3/16" x 3" o.d.) (2) 94518 [B]
21 Piston (1) 94403 [D]
22 Lower Cap (1) 94391 [Z]
23 Piston Adapter (1) 94388 [C]
n 24 ``O" Ring (3/32" x 1" o.d.) (1) Y325-117 [B]
25 Dowel Pin (1/4" o.d. x 7/8" long) (1) Y148-37 [C]
n 26 ``O" Ring (1/8" x 1-9/16" o.d.) (1) Y325-219 [B]
n 27 ``O" Ring (3/32" x 11/16" o.d.) (1) Y325-112 [B]
28 Bushing (1) 94374 [C]
n 29 Rod Seal (1) 93921 [U]
30 Base - LM2350E-X1 (1) 94536 [C]
- LM2350E-X2 (1) 94536-1 [C]
31 Nut (1/4" - 20) (4) 93828 [SS]
32 Ground Screw (#10 - 32 x 1/4") (1) 93005 [C]
n 33 Gasket (1) 70834 [Co]
34 Extension Tube
- LM2350E-2X (7.531'') (1) 94401-2 [C]
- LM2305E-3X (20.281'') (1) 94401-3 [C]
- LM2305E-4X (28.781'') (1) 94401-4 [C]
- LM2305E-6X (10.281'') (1) 94401-6 [C]
n 35 Gasket (1) 70837 [Co]
36 Piston Rod (1) 94385 [C]
37 Connecting Pin (1) 90274 [C]
n 38 Cotter Pin (1/16" x 1/2" long) (1) Y15-21 [C]
39 Connector - LM2350E-2X (3.457") (1) 94340-2 [C]
- LM2350E-3X (16.207") (1) 94340-3 [C]
- LM2350E-4X (24.707") (1) 94340-4 [C]
- LM2350E-6X (6.207") (1) 94340-6 [C]
Piston & Tube Ass'y
(includes 40 - 44)
(1) 71523
40 Lower Suction Tube (1) [C]
41 Plunger (1) [C]
42 Ball Stop (1) 83276 [C]
43 Ball (9/32" dia.) (1) Y16-209 [C]
44 Adapter (1) 70817 [C]
n 45 Guide Washer (1) 71524 [Co]
46 Spacer (1) 72392 [C]
47 Retaining Ring (.763" o.d.) (1) Y147-68 [C]
48 ``U" Cup (3/16" x 11/16" o.d.) (1) Y186-4 [B]
49 Guide Spacer (1) 76705 [T]
50 Valve Body (1) 76704 [SH]
n Foot Valve Ass'y
(includes 47 - 50)
(1) 60940
n 51 Gasket (1) F21-65 [Co]
52 Valve Seat (1) 6797 [C]
53 Primer Rod (1) 94446 [C]
n54 Retainer Ring (1) 94397 [C]
55 Primer (1) 94400 [C]
56 Primer Tube (1) 94399 [C]
: 57 Bung Assembly (includes 58) (1) 67145-2 [ZA]
: 58 Thumb Screw (1/4" - 20 x 1") (3) Y66-59-C [C]
: Items 57,58 not with -6X models
n Parts in Repair Kit 637227
OPERATING AND SAFETY PRECAUTIONS
WARNING EXCESSIVE INLET PRESSURE. Can cause exĆ
plosion resulting in severe injury or death. Do not exceed maxĆ
imum operating pressure of 7500 psi (517 bar) at 150 psi (10.3
bar) inlet air pressure. Do not run pump without using a regulaĆ
tor to limit air supply pressure to the pump.
WARNING EXCESSIVE MATERIAL PRESSURE. Can cause
equipment failure resulting in severe injury or property damĆ
age. Do not exceed the maximum material pressure of any
component in the system.
Replacement warning label is available upon request, PN \ 94520.
PUMP RATIO X
INLET PRESSURE TO PUMP MOTOR
= MAXIMUMPUMP
FLUIDPRESSURE
Pump ratio is an expression of the relationship between the pump motor area and
the lower pump end area. EXAMPLE: When 150 p.s.i. (10.3 bar) inlet pressure is
supplied to the motor of a 50:1 ratio pump it will develop a maximum of 7500 p.s.i.
(517 bar) fluid pressure (at no flow) - as the fluid control is opened, the flow rate
will increase as the motor cycle rate increases to keep up with the demand.
NOTICE: Thermal expansion can occur when the fluid in the mateĆ
rial lines is exposed to elevated temperatures. Example: Material
lines located in a non-insulated roof area can warm due to sunlight.
Install a pressure relief valve in the pumping system.