beautypg.com

Operations, English, Fine, manual tuning – Marantz ST6000 User Manual

Page 6: Direct tuning, Adjusting current time, Listening to radio

background image

ENGLISH

2

3. FINE, MANUAL TUNING

This function used for selection the manual tuning of the fine tuning
mode.
Fine tuning mode is available only in the FM mode.

1.

Press the

TUNING MODE

button.

2.

Every time you press this button, the following will be displayed
FINE

MANUAL.

a. In FINE (Tuning) mode

When you try press the

TUNING

5

button, the frequency will be se-

lected by 10 kHz step to

±

50 kHz. Then, it will automatically be set to

the MANUAL mode in 4 second.

b. In MANUAL (Tuning) mode

1.

Press the

TUNING

5

button in the FM band, then the frequency

will be selected by 50 kHz step.

2.

In the MW band, the frequency will be selected by 10 kHz step.

4. DIRECT TUNING

1.

Press the

F. DIRECT

(frequency direct) button

2.

Next press the numeric (0 to9) button.

For example: FM 98.10 MHz

a. FM is chosen with BAND (or TUNER) button on remote controller.

b. Press the F. DIRECT (Frequency Direct) button.

c. Press the numeric button of “

9

”.

d. Press the numeric button of “

8

”.

e. Press the numeric button of “

1

”.

f. Press the numeric button of “

0

”.

g. The display fixed 98.10 MHz and broadcast station received.

MW, LW band is same as above operations.

5. ADJUSTING CURRENT TIME

You can adjust the current time regardless of power on/standby.

1.

Press the

TIME ADJ

button. Then “Hour display” indicator will blink.

2.

The hour is set with the

TUNING

5

button.

3.

Press the

NEXT

button. Then “minute display” indicator will blink.

4.

The minute is set with the

TUNING

5

button.

5.

Press the

NEXT

button.

OPERATIONS

1. MEMORY PRESETTING

a. Manual operation

For example: presetting FM 90.1 M Hz, to Preset number. 10

1.

Select the FM by using the

BAND

button.

2.

Tune to 90.1 MHz by using the

TUNING

5

button.

3.

Press the

MEMO

button briefly (for less than 0.5 second) Then,

“MEMO” will bricking in the florescent tube display.

4.

Select the preset number by using the

TUNING

5

button.

5.

MEMO

button pushed again, 90.1 MHz (broadcast station) was able

to be memorized in number 10 by this.

Note:

Be sure to select the antenna A or B memorization when you preset
manual memory in FM broadcast.

b. Automatic operation

1.

Select the desired broadcasting (FM or AM) by using the

BAND

but-

ton.

2.

Press the

MEMO

button slightly longer than 1.5 second does.

Then, broadcasting will be automatically received, and as many

broadcasting station are received well will be memorized preset num-
ber-01 after another

3.

Check the broadcasting station by using the

TUNING

5

button.

Note:

1. In the case of FM automatic presetting, the antenna A, B selector

is set to “A” automatically,

And the broadcasting station is scanned twice. The stations that

have stronger broadcasting signal are preset in the first time.;
weaker ones are preset in the second time.

2. If a new broadcasting station is preset into a channel the broad-

casting station which has been preset into that position aria will be
automatically erased.

3. In mountainous or remote area broadcasting stations which have

weak broadcasting signals cannot be automatically preset into the
memory.

4. Max. 30 broadcasting stations each for FM, AM bands can be

preset.

2. LISTENING TO RADIO

1.

Select FM or AM by using the

BAND

button.

2.

Tune to the desired broadcast by using the

TUNING

or

PRESET

5

button.

3.

FM broadcasting is set up to “STEREO” mode

If the broadcasting signal is weak, or if there is a large amount of

interference in FM stereo broadcast, change the monaural mode by
presetting the

FM MODE

button.

4.

Select the IF BAND (FM bandwidth)

Select the NARROW bandwidth by pressing this button if the broad-

cast signal is interfered with adjacent broadcast in the FM .

blink

blink

blink