Garmin 190-01178-00 User Manual
Ais 300 installation instructions, Safe compass distance, Selecting locations for the ais 300 components
![background image](/manuals/107249/1/background.png)
Use these instructions to install the Garmin
®
AIS 300 Automatic Identification System (AIS) Class B receiver device. Compare the contents
of this package with the packing list on the box. If any pieces are missing, contact your Garmin dealer immediately.
Use the following instructions to install the AIS 300 device. Details for the following steps are included in this document:
1. Select locations for the AIS components.
2. Mount the AIS 300 receiver box.
3. Connect the AIS 300 to power.
4. Connect the AIS 300 to a VHF antenna and to an optional VHF radio (
5. Connect the AIS 300 to a NMEA 2000 network or to a NMEA 0183-compatible chartplotter (optional -
WARNING
When navigating, carefully compare information provided by the unit to all available navigation sources, including information from visual
sightings, local waterway rules and restrictions, and maps. For safety, always resolve any discrepancies or questions before continuing
navigation.
Use this unit only as a navigational aid. Do not attempt to use the unit for any purpose requiring precise measurement of direction, distance,
location, or topography.
This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or
reproductive harm. This Notice is provided in accordance with California’
for more
information.
CAutIoN
Wear safety goggles and a dust mask when drilling, cutting, or sanding.
Safe Compass Distance
Ensure that you install the AIS 300 receiver box at least 15
3
/
4
in. (40 cm) from any compass. Test your compass to verify that it operates
correctly when the AIS 300 is operating.
Selecting Locations for the AIS 300 Components
Use the wiring layout diagrams starting on
to determine how to best organize the AIS 300 components on your boat. Ensure that the
cables reach all components before permanently mounting any component.
Mounting the AIS 300 Receiver Box
Install the AIS 300 receiver box below deck on a bulkhead. Select a location that is dry and protected from washdown. Ensure that the
location is well ventilated and away from objects that generate heat. Ensure that the receiver box is at least 15
3
/
4
in. (40 cm) from any
compass to avoid interference.
Needed tools
Drill and drill bits
Number 2 Phillips screwdriver
to mount the receiver box:
1. Ensure that the chosen location is dry, protected from washdown, and well-ventilated.
2. Use the receiver box as a template, and use a pencil to mark the holes in the four corners. Do not drill through the receiver box.
3. Drill four
1
/
8
in. (3 mm) pilot holes.
4. Mount the receiver box using the included 20 mm M 3.5 screws. You can also use bolts, washers, and nuts (not included) to mount the
receiver box if the mounting surface is suitable.
•
•
March 2010
190-01178-00 Rev. B
Printed in China
AIS 300 Installation Instructions
Document Outline
- AIS 300 Installation Instructions
- Safe Compass Distance
- Selecting Locations for the AIS 300 Components
- Mounting the AIS 300 Receiver Box
- AIS 300 Wiring Layout: AIS 300 Connected to a Garmin Chartplotter Through NMEA 2000
- AIS 300 Wiring Layout: AIS 300 Connected to a Garmin ChartplotterThrough NMEA 0183
- Connecting the Receiver Box to Power
- Installing the AIS 300 Power Toggle
- Connecting a VHF Antenna to the AIS 300
- Connecting the AIS 300 to a NMEA 2000 Network (Optional)
- Connecting the AIS 300 to a NMEA 0183 Device (Optional)
- Using the AIS 300
- Appendix