Emerson Autochangeover Controllers AC8 User Manual
Emerson Computer Accessories
Table of contents
Document Outline
- 1.0 Introduction
- 2.0 Installation
- 3.0 Wiring and Connections
- 3.1 Wiring Specifications
- 3.2 Connecting Digital Inputs and Digital Outputs
- 3.3 Connecting Analog Inputs
- 3.4 Connecting Common Alarm Outputs
- 3.5 EIA422 SiteScan Web Connector
- 3.6 Communications Connections
- 4.0 Overview of Menus
- 5.0 View Status Options
- 6.0 Silence Alarm & Backup Log Files (Service Terminal Interface)
- 7.0 System and Control Options
- Table 14 Valid characters for data entry
- 7.1 Login
- 7.2 Setup System - Overview
- 7.3 Setup System - Setup Inputs
- 7.4 Setup System - Setup Common Alarm
- 7.5 Setup System - Setup Sensor
- Table 17 Default settings - analog sensor inputs
- 7.5.1 Identify the Sensor as Connected
- 7.5.2 Change Sensor Label (Name)
- 7.5.3 Change Units Label
- 7.5.4 Change 4 mA Value
- 7.5.5 Change 20 mA Value
- 7.5.6 Change Offset Value
- 7.5.7 Define Sensor as Alarmable or Event
- 7.5.8 Set Up Alarmable Sensors in Latched or Unlatched Mode
- 7.5.9 Change Low Setpoint
- 7.5.10 Change High Setpoint
- 7.5.11 Set Up Delay Time
- 7.6 Setup System - Setup Zones
- 7.7 Setup System - Setup Outputs
- Table 19 Default settings - digital outputs
- 7.7.1 Define Output as Normally Open or Normally Closed
- 7.7.2 Define Operating or Standby Mode
- 7.7.3 Enable or Disable an Output Device in Alarm Status
- 7.7.4 Enable or Disable a Device during Emergency Power Operation
- 7.7.5 Configure Output for Loss of Power (“Fail-Safe”)
- 7.8 Setup System - Setup Modem & Pagers
- 7.9 Setup System - Setup System Info
- Figure 11 Menu overview - Setup System Info menu
- 7.9.1 Change Password
- 7.9.2 Change Date & Time/Automatic Daylight Saving Time
- 7.9.3 Setup Site ID
- 7.9.4 Connect Battery
- 7.9.5 Backup and Upload Configuration File (Service Terminal Interface only)
- 7.9.6 Setup Serv Ph Num - Enter Phone Number
- 7.9.7 Setup Serv Ph Num - Communications Check (Service Terminal Interface only)
- 7.9.8 Factory Defaults
- 7.9.9 Perform Firmware Update (Service Terminal Interface only)
- 7.9.10 Initiate Remote Alarm Test (Service Terminal Interface only)
- 7.10 Setup Operation
- 7.11 Setup System - Setup I/O Matrix
- 7.12 Override Output
- 7.13 Clear Alarms & Logs
- 8.0 Specifications
- Appendix A - Service Terminal Interface
- A.1 Comparison of Functions: LCD and Service Terminal Interface
- A.2 Connecting to the Service Terminal Interface
- A.3 Overview of Menus
- A.4 View Status Menus
- A.5 Silence Alarm & Back Up Log Files (Service Terminal Interface only)
- A.6 Setup Menu
- Main Menu
- Login Menu
- Setup Menu
- A.6.1 Setup Inputs
- A.6.2 Setup Common Alarm
- A.6.3 Setup Sensor
- A.6.4 Setup Zones
- A.6.5 Setup Output
- A.6.6 Setup Modem & Pagers
- A.6.7 Setup System Info
- Change Password
- Set Date & Time/Automatic Daylight Saving Time
- Setup Site ID
- Connect Battery
- Backup and Upload Configuration File (Service Terminal Interface only)
- Setup Service Phone Number
- Factory Defaults
- Firmware Update (Service Terminal Interface only)
- Initiate Remote Alarm Test (Service Terminal Interface only)
- A.6.8 Setup Operation
- A.6.9 Override Output
- A.6.10 Clear Alarms & Logs
- A.6.11 Setup I/O Matrix
- Appendix B - Default Settings Quick Reference Guide