PLANET POE-E101 - Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
Introduction
1.1 Packet Contents
Thank you for purchasing PLANET POE-E101 IEEE
802.3af Power over Ethernet Extender, your Power
over Ethernet Extender package shall contains following
contents:
Check the contents of your package for following parts:
Power over Ethernet Extender x 1 z
User's Manual x 1 z
If any of these pieces are missing or damaged, please
contact your dealer immediately, if possible, retain the
carton including the original packing material, and use
them against to repack the product in case there is a
need to return it to us for repair.
1.3 Technical Specification
Model POE-E101
Interfaces
LAN IN
1 x 10/100Base-TX Ethernet with IEEE
802.3af PoE “Data + DC” in Auto
MDI/MDI-X, Auto-negotiation RJ-45
connector
LAN OUT
1 x 10/100Base-TX Ethernet with IEEE
802.3af PoE “Data + DC” out Auto
MDI/MDI-X, Auto-negotiation RJ-45
connector
Power over Ethernet
PoE
Standard
IEEE 802.3af Power over Ethernet
PoE Power
Supply Type
Mid-Span / Type B
PoE Power
Output
48V DC, 270mA, Max. 13 Watts
Power Pin
Assignment
4/5(+), 7/8(-)
2.2 Ports Connection
IN Port
Connect the PoE IN port from following
802.3af PSE device through a CAT-5e/6
UTP cable:
• PoE Injector
• PoE Injector Hub
• PoE Ethernet Switch
• Previous POE-E101
OUT Port
Connect the PoE OUT port to following
802.3af PD device through a CAT-5e/6
UTP cable:
• PoE IP Camera
• PoE VoIP Phone
• PoE Wireless AP
• PoE Splitter
• Next POE-E101
2.3 LED Definition:
LED Color Function
PoE IN Green
Lights to indicate the port is
providing 48V DC in-line power.
LNK/
ACT
Green
Lights to indicate the port is link up.
Blink: indicate that the extender is
actively sending or receiving data
over IN port.
PoE
OUT
Green
Lights to indicate the port is
providing 48V DC in-line power.
Standards Conformance
Regulation
Compliance
FCC Part 15 Class A, CE
Standard
Compliance
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 10/100Base-TX Fast
Ethernet
IEEE 802.3af Power over Ethernet PSE
/ Mid-Span
IEEE 802.3af Power over Ethernet PD /
Mid-Span
IEEE 802.3x Flow Control
Environment
Operating
Temperature:
0 ~ 50 Degree C
Relative Humidity:
0 ~ 95% (non-condensing)
Storage
Temperature:
-40 ~ 85 Degree C
Relative Humidity:
5 ~ 95% (non-condensing)
1.2 Key Features
Complies with z IEEE 802.3af Power over Ethernet
Extends the range of PoE an additional 100 meters z
(328ft.)
Forwards both Ethernet z data and PoE power to
remote device
Auto-detect and protect of PoE equipment from being z
damaged by incorrect installation
Multiple units, daisy-chain installation support z
No external power cable installation required z
Compact size, Wall-mountable design z
Plug-and-Play z installation
Hardware Specification
Data Rate
10/100Mbps
Switch
Architecture
Store-and-Forward
Switch
Throughput
148810pps@64Bytes
Latency 7.840µs
Maximum
Frame Size
1552Bytes
Flow Control
Back pressure for Half-Duplex
IEEE 802.3x Pause Frame for Full-Duplex
LED
Indicators
• 1 x PoE IN (Green)
• 1 x LAN Data (Green)
• 1 x PoE OUT (Green)
Protection
ESD (Ethernet) : 6KV (TBD)
Surge (EFT for power) : 6KV (TBD)
Dimension
(W x D x H)
94 x 70 x 26 mm
Weight 215g
Power
Requirement IEEE 802.3af compliant with voltage
within 44V-56V DC
Power
Consumption
2 Watts (system maximum)
Mechanical Metal / Wall Mountable
Cable TIA/EIA-568, Category 5/5e cable
Hardware Description
2.1 Product Outlook
Hardware Installation
This product provides two different running speeds –
10Mbps, 100Mbps in the same device and automatically
distinguishes the speed of incoming connection.
This section describes the hardware features of
POE-E101. Before connecting any network device to the
POE-E101, read this chapter carefully.
3.1 Before Installation
Before your installation, it is recommended to check
your network environment. If there is any far away IEEE
802.3af devices need to power on, the POE-E101 can
provide you a way to supply power for this Ethernet
device conveniently and easily.
The POE-E101 is installed between the PSE (Power Source
Equipment) and the PD (Powered Device); it is powered
by PSE and forwards the Ethernet data and remaining
POE power to the PD. The POE-E101 doesn’t require
an external power supply and it can be installed easily
just plug and play; that means the operator does not
need to configure the POE-E101. The POE-E101 injects
power to the PDs without affecting the data transmission
performance. It offers a cost effective and quick solution
to extend power and data an additional 100m.
Note
The POE-E101 can be installed with third-party
device if the device complied with IEEE 802.3af
standard.