Parkside PKZ 180 B2 - Manual (Page 31)

28 PKZ 180 B2
GB
MT
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off . Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may aff ect the
power tool’s operation. If damaged, have
the power tool repaired before use. Many ac-
cidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations diff erent from those
intended could result in a hazardous situation.
5. Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
b) Always arrange for the exchange of the plug
or the power cord to be carried out by the
manufacturer of the appliance or by its ap-
proved customer services. This will ensure that
the safety of the power tool is maintained.
Device-specifi c safety instructions
■ This appliance may not be used by children or
people with reduced physical, sensory or mental ca-
pabilities or a lack of experience and knowledge.
Children must not use the appliance as a plaything.
Cleaning and user maintenance tasks may not be
carried out by children unless they are supervised.
■ Avoid using the compressor at temperatures
below +5 degrees.
■ Never leave the compressor unsupervised while
it is in use.
■ Ensure that the ON/OFF switch is turned off
when connecting to the mains power supply.
■ Caution! Operate the compressor only for a
short time. The appliance may overheat if oper-
ated continuously for longer than 10 minutes.
Switch the appliance off immediately and allow
it to cool down for at least 10 minutes.
■ Risk of injury! Do not pump any objects up to
more than the intended pressure. They could
burst and cause injury and/or material damage.
■ Do not exceed the permissible output range of
the compressor. Do not pump up any lorry,
tractor or other large tires.
■ Do not work with any materials that are or could
be easily infl ammable or explosive.
■ Never use the appliance for purposes other
than the ones for which it was designed.
IB_108972_PKZ180B2_LB5.indb 28 IB_108972_PKZ180B2_LB5.indb 28 13.01.15 08:59 13.01.15 08:59