H3C Technologies H3C WX5500E Series Access Controllers User Manual
Layer 2-lan switching configuration guide
Table of contents
Document Outline
- Title Page
- Preface
- Contents
- Configuring Ethernet interfaces
- Ethernet interface naming conventions
- Performing general configurations
- Configuring basic settings of an Ethernet interface
- Shutting down an Ethernet interface
- Configuring generic flow control on an Ethernet interface
- Configuring physical state change suppression on an Ethernet interface
- Configuring loopback testing on an Ethernet interface
- Configuring jumbo frame support
- Enabling auto power-down
- Setting a statistics polling interval
- Configuring a Layer 2 Ethernet interface
- Layer 2 Ethernet interface configuration task list
- Setting speed options for autonegotiation on an Ethernet interface
- Configuring storm suppression
- Enabling loopback detection on an Ethernet interface
- Setting the MDI mode of an Ethernet interface
- Enabling bridging on an Ethernet interface
- Testing the cable connection of an Ethernet interface
- Configuring storm control on an Ethernet interface
- Displaying and maintaining an Ethernet interface
- Configuring loopback and null interfaces
- Bulk configuring interfaces
- Configuring the MAC address table
- Overview
- Configuration procedure
- Displaying and maintaining MAC address tables
- MAC address table configuration example
- Configuring MAC Information
- Configuring Ethernet link aggregation
- Overview
- Ethernet link aggregation configuration task list
- Configuring an aggregation group
- Configuring an aggregate interface
- Configuring load sharing criteria for link aggregation groups
- Displaying and maintaining Ethernet link aggregation
- Ethernet link aggregation configuration examples
- Configuring port isolation
- Configuring spanning tree protocols
- STP
- RSTP
- PVST
- MSTP
- Protocols and standards
- Spanning tree configuration task lists
- Setting the spanning tree mode
- Configuring an MST region
- Configuring the root bridge or a secondary root bridge
- Configuring the device priority
- Configuring the maximum hops of an MST region
- Configuring the network diameter of a switched network
- Configuring spanning tree timers
- Configuring the timeout factor
- Configuring the maximum port rate
- Configuring edge ports
- Configuring path costs of ports
- Configuring the port priority
- Configuring the port link type
- Configuring the mode a port uses to recognize and send MSTP packets
- Enabling outputting port state transition information
- Enabling the spanning tree feature
- Performing mCheck
- Configuring digest snooping
- Configuring no agreement check
- Configuring protection functions
- Displaying and maintaining spanning tree protocols
- Spanning tree configuration examples
- Configuring BPDU tunneling
- Configuring VLANs
- Overview
- Configuring basic VLAN settings
- Configuring basic settings of a VLAN interface
- Configuring port-based VLANs
- Configuring MAC-based VLANs
- Configuring protocol-based VLANs
- Configuring IP subnet-based VLANs
- Displaying and maintaining VLANs
- Configuring super VLANs
- Configuring isolate-user-VLANs
- Configuring voice VLANs
- Overview
- Configuration prerequisites
- Configuration restrictions and guidelines
- Configuring QoS priority settings for voice traffic on an interface
- Configuring a port to operate in automatic voice VLAN assignment mode
- Configuring a port to operate in manual voice VLAN assignment mode
- Displaying and maintaining voice VLANs
- Voice VLAN configuration examples
- Configuring GVRP
- Overview
- GVRP configuration task list
- Configuring GVRP functions
- Configuring the GARP timers
- Displaying and maintaining GVRP
- GVRP configuration examples
- Configuring LLDP
- Overview
- LLDP configuration task list
- Performing basic LLDP configuration
- Configuring CDP compatibility
- Enabling LLDP to automatically discover IP phones
- Configuring LLDP trapping
- Displaying and maintaining LLDP
- LLDP configuration examples
- Configuring service loopback groups
- Configuring MVRP
- Index