Sloan ETF-80 Faucet - Manual (Page 3)

3
1A ETF-295-A (for ETF-80) Single
Hole 4” Trim Plate
A
Slide Rubber Faucet Gasket onto Faucet Shank. Ensure that Roll
Pin on base of Faucet fits into hole in Rubber Faucet Gasket.
Note: When installing with a Sloan Mixing Valve, install Faucet and Trim Plate before installing Mixing Valve. For complete installation guidelines, refer to
the Installation Instructions supplied with the Sloan mixing valve.
B
Insert Hex Bolts into Black Plastic Base Plate (if sink has only a
center hole, see note above). Place Chrome Cover Plate over
Black Plastic Base Plate. Slide Trim Plate assembly onto Faucet
Shank. Align Roll Pin with small hole in Trim Plate assembly.
Note: If Trim Plate is used on a sink with a center hole only, Trim Plate
Bolts are not used. Apply plumber’s putty to underside of Trim Plate to
prevent Faucet from rotating.
C
Insert Trim Plate Bolts through the 4 inch (102 mm) spread deck
holes and Faucet Shank through the 1 inch (25 mm) minimum
diameter deck hole. Secure Trim Plate to Deck using the large
Plate Washers and Hex Nuts supplied. Secure Faucet from below
Deck using the Flange Nut supplied.
ROLL PIN
RUBBER
FAUCET GASKET
COVER PLATE
BLACK PLASTIC
BASE PLATE
DECK
FAUCET SHANK
TRIM PLATE
HEX BOLTS (2)
PLATE
WASHERS (2)
HEX NUTS (2)
FLANGE NUT
1 Install Faucet Spout and Trim Plate — Refer to the appropriate step (1A-1C) for
your application.
1B ETF-662-A (for ETF-880) Single
Hole 4” Trim Plate
A
Slide Rubber Faucet Gasket onto Faucet Shank. Ensure that Roll
Pin on base of Faucet fits into hole in Rubber Faucet Gasket.
B
Slide Trim Plate and Back-up Spacer onto Faucet Shank. Align Roll
Pin with small slot in Trim Plate.
C
Secure Faucet from below Deck using the Flange Nut supplied.
ROLL PIN
RUBBER FAUCET
GASKET
TRIM PLATE
BACK-UP
SPACER
DECK
FAUCET SHANK
FLANGE NUT
1C ETF-510-A (for ETF-80/880) Single
Hole 8” Trim Plate
A
Slide Rubber Faucet Gasket onto Faucet Shank. Ensure that Roll
Pin on base of Faucet fits into hole in Rubber Faucet Gasket.
B
Slide Trim Plate and Back-up Spacer onto Faucet Shank. Align Roll
Pin with small slot in Trim Plate.
C
Slide Washer Gaskets over Studs. Place Studs and Faucet Shank
through Base Gasket and holes in Deck.
D
Secure Trim Plate from below Deck using the two (2) Fender
Washers and two (2) Finger Nuts supplied.
E
Secure Faucet from below Deck using the Flange Nut supplied.
ROLL PIN
RUBBER
FAUCET
GASKET
TRIM PLATE
STUD
DECK
FAUCET SHANK
WASHER
GASKET (2)
BASE
GASKET
BACK-UP
SPACER
FENDER
WASHER (2)
FINGER NUT (2)
FLANGE NUT
ETF-880 FAUCET
ETF-80 FAUCET