Play operation, Tape deck operation, 5english – Marantz PM-14mkII User Manual
Page 6
5
ENGLISH
PLAY OPERATION
Playing a record
1
Set the
INPUT SELECTOR
switch
q
to the PHONO position.
2
Operate the record player.
3
Adjust the volume with the
VOLUME
knob
r
.
Note:
• Set the volume to the minimum when exchanging the record player
cartridge or lowering the stylus onto a record.
• Do not subject the record player to vibrations while playing records.
Vibrations may cause the stylus to jump and scratch the record.
• If the record player is placed near the speakers, howling may occur
and this will prevent the volume from being increased.
• Do not turn the power supply off while the stylus is still on the record.
Playing a CD
1
Set the
INPUT SELECTOR
switch
q
to the CD position.
2
Operate the component connected to the selected jack.
3
Adjust the volume with the
VOLUME
knob
r
.
Playing from LINE 1 to LINE 3
Playing a component which is connected to one of the LINE 1 to LINE 3
jacks on the rear panel.
1
Set the
INPUT SELECTOR
switch
q
to one of the LINE 1 to
LINE 3 positions.
2
Operate the component connected to the selected jack.
3
Adjust the volume with the
VOLUME
knob
r
.
TAPE DECK OPERATION
Playing a Tape
1
Select the tape deck to be used (TAPE 1 or TAPE 2) with the
INPUT SELECTOR
switch
q
.
2
Operate the tape deck and play a tape which has something
recorded on it.
3
Adjust the volume with the
VOLUME
knob
r
.
Recording on a Tape
Use the following procedure to record a source such as a record player,
tuner, CD player, etc onto a tape.
[When recording from a CD player]
1
Set the
REC SELECTOR
switch
!2
to the CD position.
2
Start playing the program source.
3
Operate the tape deck and start recording.
•
The source to be recorded can be selected with the
REC SELECTOR
switch
!2
regardless of the setting of the
INPUT SELECTOR
switch
q
.
To record the record player
signal
To stop the output to the tape
when recording is not
required
To record the CD signal
To record the signal
connected to one of LINE 1
through LINE 3
Using the REC SELECTOR switch !2 to copy a prerecorded tape
Regardless of the program source selected with the
INPUT SELEC-
TOR
switch
q
, the REC SELECTOR switch
!2
can be switched to 1 to
2 or 2 to 1 to copy from TAPE 1 to TAPE 2 or from TAPE 2 to TAPE 1.
• While copying tapes, you can listen to another program source by
selecting it with the INPUT SELECTOR switch
q
.
• TAPE COPY 1 to 2 allows you to copy the signal from the tape deck
connected to TAPE 1 to the tape deck connected to TAPE 2. TAPE
COPY 2 to 1 allows you to copy the signal from the tape deck con-
nected to TAPE 2 to the tape deck connected to TAPE 1.
TEMP
POWER
PHONES
SPEAKERS
A+B
B
A
OFF
PHONO
LINE 3
LINE 2
LINE 1
CD
OFF
REC SELECTOR
INPUT SELECTOR
CD SELECTOR
BAL.
UNBAL.
PHONO
CD
LINE 1
LINE 2
LINE 3
CD-R
TAPE
BASS
0
2
2
4
4
6
6 +
–
(dB)
0
2
2
4
4
6
6 +
–
(dB)
TREBLE
SOURCE
DIRECT
ON
OFF
BALANCE
RIGHT
LEFT
0
2
4
7
10
12
13
14
15
17
19
25
21
29
32
38
40
48
52
66
(-dB)
VOLUME
INTEGRATED AMPLIFIER PM-14mkII
CD-R
COPY
TAPE
CD-R
TAPE
TEMP
POWER
PHONES
SPEAKERS
A+B
B
A
OFF
PHONO
LINE 3
LINE 2
LINE 1
CD
OFF
CD-R
COPY
REC SELECTOR
INPUT SELECTOR
CD SELECTOR
BAL.
UNBAL.
PHONO
CD
LINE 1
LINE 2
LINE 3
CD-R
TAPE
BASS
0
2
2
4
4
6
6 +
–
(dB)
0
2
2
4
4
6
6 +
–
(dB)
TREBLE
SOURCE
DIRECT
ON
OFF
BALANCE
RIGHT
LEFT
0
2
4
7
10
12
13
14
15
17
19
25
21
29
32
38
40
48
52
66
(-dB)
VOLUME
INTEGRATED AMPLIFIER PM-14mkII
TAPE
CD-R
TAPE
..........
PHONO position
.......... OFF position
.......... CD position
.......... Set the REC SELECTOR
switch to one of the LINE 1
through LINE 3 positions.