Legrand WMFB - Manual

1. WARNING: TEST THAT POWER IS OFF AT CIRCUIT BREAKER OR
FUSE BLOCK!
2. Determine approximate location (which joists to put it between) and
route cable(s) to joist cavity and fasten cable within 12" of proposed
opening per NEC 334.30 leaving large enough loop to later install box
after finishing floor installation.
3. Determine box location and
drill four 3/4" diameter holes
using
template “A” for
WMFB1 series or template
“B” for WMFB2 series.
Note: When installing tile,
marble or hardwood flooring,
you may want to wait to cut
the
opening during the
finished floor installation to
ensure the opening in the
floor does not end up in the
middle of a tile or hardwood
plank.
4. Cut remainder of opening
using the appropriate tem-
plate
by connecting the
edges of the holes.
5. Complete the finished floor
installation up to the
previously cut opening,
ensuring the box will still fit
into opening.
6. Pull the wires through the
opening in floor and into the
auto-clamp feature. Knock-
outs are provided for low
voltage cables if desired. If
Romex-type
NM cable is
routed through the knockouts,
an approved wire clamp must
be used.
7. Attach box to flooring using
either the four #6 drywall
screws included or use the
assembled swing brackets.
Tighten screws firmly. When
assembling
to carpet, the
carpet may need to be
trimmed back to ensure the
box flange sets flush. Trim only
the carpet loops/shag and
leave the carpet backing under
the flange for security. Cut the
padding back 1-2" larger than
the opening to ensure the
device seats firmly and flush to
the floor.
8. Install device(s) per appropriate
installation instructions below.
WMFB-1 & WMFB-2 SERIES FLOOR BOX
INSTALLATION INSTRUCTIONS
NOTICE: READ BEFORE INSTALLING DEVICE
NEW/OLD CONSTRUCTION
FEATURES AND BENEFITS
3
2
4
7
6
Available Catalog #’s
Cat # Description
WMFB1DR* 1 gang floor box, Duplex Cover, Duplex 15 amp Receptacle
WMFB1KS2* 1 gang floor box, Single Cover, Two Port Keystone Jack
WMFB1KS4* 1 gang floor box, Duplex Cover, Four Port Keystone Jack
WMFB1SR* 1 gang floor box, Single Cover, Single 15 amp Receptacle
WMFB1SRKS1* 1 gang floor box, Duplex Cover, Single 15 amp Receptacle &
1 Port Keystone Jack
WMFB2DR2* 2 gang floor box, Two Duplex Cover, Two Duplex 15 amp
Receptacles
WMFB2DRKS4* 2 gang floor box, Two Duplex Cover, Duplex 15 amp Receptacle
& 4 Port Keystone Jack
WMFB2KS8* 2 gang floor box, Two Duplex Cover, Two 4 Port Keystone Jack
*denotes: B = Brass Cover or N = Nickel Plated Cover
NOTICE: For installation only by a electrician or other
qualified person in accordance with the National Electrical
Code, Canadian Electrical Code, local Codes and the
instructions on this sheet.
CAUTION: RISK OF ELECTRICAL SHOCK. Turn off all power
to circuit before installing this device. Improper wiring of any
electrical device can cause serious injury or death.
CAUTION: Connect only copper or copper-clad wire to the
device in this package. Do not connect aluminum wire to this
device.
NOTE: USE ONLY ELECTRICAL MOUNTING BOX
PROVIDED.
U.S. and International: 60 Woodlawn Street • West Hartford, CT 06110 • 1-800-621-0049 • FAX 860-232-2062 • Outside U.S.: 860-233-6251 P/N 340771 Rev. B
Canada: 570 Applewood Crescent • Vaughan, Ontario L4K 4B4 • 1-800-723-5175 • FAX 905-738-9721
www.wiremold.com
Printed in USA
-
-
-
-
Ø
Ø
• Exclusive Dual Voltage Single Gang Floor Box, great for TV’s,
Telephones and Laptop connections
• Complete line of low voltage connectors available through
Pass and Seymour (www.passandseymour.com).
• Installs before or after the floor is completed to ensure the best
possible finish
• Easy rectangular floor cut out
• Swing bracket mounting option, superior for tile or marble floors
• No messy caulking needed to meet scrub water requirements
• Plastic Boxes do not require ground bonding in most applications