Weston Cuber/Tenderizer - Manual (Page 4)

-4- -5-
ASSEMBLY INSTRUCTIONS
1. Connect the Left and Right Legs to the
Base using the provided Allen Wrench and
Screws.
2. Using an Allen Wrench and Screws,
attach the Left and Right Legs to the Lower
Housing. Figure 1
3. Install the Chute to the Top Housing
using an Allen Wrench, Screws.
4. Insert the Blade Rack Assembly into
the Lower Housing, guiding the Drive
Shaft into the bearing journals. Make sure
the teeth of the Blade Racks are properly
meshed together.
5. Position the Top Housing onto the Lower
Housing and line up the screw holes.
6. Secure the Top Housing to the Lower
Housing using the Housing Thumbscrews.
DO NOT OVERTIGHTEN!
7. Insert the Left Comb and Right Comb
into the Top Housing.
Figure 2
NOTE: The Left Comb is marked with an
“L” on the upper portion of the Comb. The
Top Housing is marked with an “L Comb”
and “R Comb” to aid in Comb installation.
8. Install Handle onto the Blade Rack Shaft.
Secure the Handle to Blade Rack Shaft with
the Handle Thumbscrew .
GENERAL SAFETY RULES
READ AND FULLY UNDERSTAND ALL INSTRUCTIONS
AND WARNINGS PRIOR TO USING THIS PRODUCT.
YOUR SAFETY IS MOST IMPORTANT! FAILURE TO
COMPLY WITH PROCEDURES AND SAFEGUARDS MAY
RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE.
REMEMBER: YOUR PERSONAL SAFETY IS YOUR
RESPONSIBILITY!
WARNING!
SAVE THESE INSTRUCTIONS!
Refer to them often and use them to instruct others.
1. NEVER REACH INTO the Cuber/
Tenderizer. Doing so could cause serious
injury. ALWAYS USE THE PROVIDED
TONGS.
2.
KEEP FINGERS CLEAR OF THE BLADES
AT ALL TIMES. Failure to do so may result in
personal injury. The Cutting Blades/Blade
Assembly is very sharp. It is recommended
to wear Kevlar, cut resistant gloves when
handling the Blades.
3. DO NOT press or push meat into the Chute
with your fingers or any other object. Doing
so may cause personal injury and/or damage
to the unit.
4. NEVER use fingers to scrape food away
from the Cuber/Tenderizer while the grinder
is in operation. SEVERE INJURY MAY
RESULT.
5.
DO NOT push the Tongs or other utensils
into the Blades.
6. NEVER LEAVE THE Cuber/Tenderizer
UNATTENDED. Close supervision is
necessary when any appliance is used near
children. This appliance is NOT to be used by
children.
7. NEVER use any accessories or parts from
other manufacturers. Doing so will VOID YOUR
WARRANTY.
8. Thoroughly clean all parts that will come
into contact with food before using the
Tenderizer/Cuber. Wash all parts by hand
and dry thoroughly. WARNING! Protective/
cut-resistant Kevlar gloves are recommended
when handling the blade assembly.
9. DO NOT attempt to tenderize meat with
bones or other hard items. Damage to the
machine will occur.
10. TIE BACK loose hair and clothing, and roll
up long sleeves before operating the Cuber/
Tenderizer. REMOVE ties, rings, watches,
bracelets, or other jewelry before operating the
Cuber/Tenderizer.
11.
DO NOT use the Cuber/Tenderizer while
under the influence of drugs, medications or
alcohol.
ADDITIONAL ACCESSORIES AVAILABLE
6” Jerky Slicer Blade 07-3302
Food-Grade Silicone Spray 03-0101-W
Kevlar Gloves Small 34-0101
Kevlar Gloves Medium 34-0102
Kevlar Gloves Large 34-0103
Cuber/Tenderizer Motor Attachment 01-0103-W
Pro-2100 Vacuum Sealer 65-0101
Vacuum Sealer Bags Multi Pack 30-0107-W
These products and many more products can be ordered by visiting
w w w . w e s t o n s u p p l y . c o m or by calling
Pragotrade LLC Toll Free at 1-800-814-4895
Monday thru Friday 8:00am-5:00pm EST.
Outside the U.S. call 440-638-3131
Figure 1
Legs
Lower
Housing
Base
Chute
Top
Housing
Blade Rack
Assembly
Blade Rack
Shaft
Figure 2
Comb