MTD 243-651B000 - Manual (Page 11)

Models 645B, 648B, 650B and 651B
PARTS LIST FOR SHREDDERS
REF.
NO.
PART
NO.
CODE DESCRIPTION
REF.
NO.
PART
NO.
CODE DESCRIPTION
1 -4840+ 142 Blade 38 736-0119 L-Wash. 5/16" I.D.*
2 710-0818 Hex Patch Bolt 3/8-24 x 2" Lg. 39 710-3008 Hex Bolt 5/16-18 X. 75" Lg.
(Gr. 8) (Used w/Keyed Engine (Gr. 5)
Crankshaft) 40 710-0380 Hex Bolt 5/16-18 X 1.75" Lg.*
710-1254 N Hex Patch Bolt 3/8-24 x 2.25" 41 681-0004 Flail Housing Ass’y.—L.H.
(Gr. 8) (Used w/Tapered 42 781-0474A Flail Housing Ass’y.—R.H.
Engine Crankshaft) 43 735-0639 Spark Plug Boot (Optional)
3 714-0114 Sq. Key 1/4 x 2.0" Lg. (Used 44 — Engine
w/Keyed Engine (Crankshaft) 45 747-0531A Release Bar
4 736-0217 L-Wash. 3/8" I.D. H.D. 46 732-0546 Torsion Spring 1.06“ Lg.
5 736-0247 FI-Wash. .406" I.D. x 1.25" O.D. 47 712-0429 Elastic Lock Nut 5/16-18 Thd.
Hdn. 48 710-0601 Hex Wash. Hd. Self-Tap Scr.
6 11459B Flail 5/16-18 X .75" Lg.
7 711-0564 Flail Spacer 49 11480 Stop Washer
8 711-0833A Clevis Pin .496" Dia. 50 736-0264 FI-Wash. 5/16" I.D.
9 711-0834 Flail Spacer w/.160" Dia. Hole 51 710-0542 Hex Bolt 5/16-18x8.38" Lg.
10 715-0249 Spring Roll Pin 1.12" Lg. 52 781-0487B Back-Up Plate
11 736-0192 FI-Wash. .531" I.D. x .94" O.D. 53 16522B Inlet Guide Ass’y.
12 681-0002 ImpeHer Ass’y- Comp. (Used 54 11481B Hopper Ass’y.
w/Keyed Engine Crank- 55 781-0509 Lower Leaf Ramp Section
shaft-Incl. Ref. 1,6, 7, 8, 9, 56 710-0286 Truss Mach. Scr. 1/4-20 x .5"*
10, 11, 12, 13, 14) 57 712-0107 Hex L-Nut 1/4-20 Thd.
681-0030 N Impeller Ass’y. Comp. (Used 58 11461B Upper Leaf Ramp Section
w/Tapered Engine Crank- 59 726-0214 Push Cap 5/8" Dia. Rod
shaft-Incl. Ref. 1,6, 7, 8, 9, 60 737-0195 Drain Elbow (5 HP B&S)
10, 11, 12, 13, 14) 737-0125 Drain Elbow (8 HP B&S)
13 781-0490 Chipper Blade 61 750-0786 Spacer .64" I.D. x .38" Lg.
14 710-1054 Flat Hd. Scr. 5/16-24 x .75" Lg. 62 738-0814 Shredder Axlef
. 15 712-0411 Hex Top L-Nut 5/16-24 (Gr. 5) 738-0813 Shredder Axleft
16 736-0119 L-Wash. 5/16" I.D.* 63 734-1600 Wheel Ass’y. Comp. (Plastic-
17 710-0825 Hex Bolt 1/4-20 x 3.75" Lg.* 10x2.5)
18 736-0142 FI-Wash. .281"I.D. X . 5 " O.D. 734-1597 Wheel Ass’y. Comp. (Steel-
19 750-0793 Chute Hinge Spacer 1.66" Lg. 1 0 x 4 )
2 0 711-0835 Clevis Pin .5" Dia. x 4.62" Lg. 734-1598 Tire Onlytt
22 712-0291 Hex Ctr. L-Nut 1/4-20 Thd.* 64 734-1455 Rim Onlytt
23 714-3010 Cotter Pin 3/32" X 5/8" 65 741-0487 Flange Bearing .632" I.D.tt
24 781-0457 Shredder Screen 66 734-0255 Air Valvett
25 714-0145 Internal Cotter Pin 3/8" Dia. 67 737-0280 Grease Fittingtt
26 781-0480 Chute Deflector Ass’y. 68 710-0895 Hex Hi-Low Scr. 1/4 x .75"
27 712-3010 Hex Nut 5/16-18 Thd. (Gr. 5) (650, 651)
28 736-0242 Bell-Wash. .345" I.D. x .88" 69 710-3038 Hex Bolt 5/16-18 X . 88" Lg.
29 720-0170 Hand Knob (650, 651)
30 747-0744A Chipper Door Rod 70 726-0205 Hose Clamp (650, 651)
31 732-0542 Torsion Spring 1.14" Lg. 71 751-0535-7 Fuel Line-7 in. (650, 651)
32 781-0489 Chipper Door 72 751-0570 N Fuel Tank Ass’y. Comp.
33 781-0475 Chipper Chute Ass’y. (650, 651)
34 736-0170 Spec. L-Wash. 5/16" I.D. 73 781-0497 N Fuel Tank Mtg. Brkt. (650, 651)
35 712-3010 Hex Nut 5/16-18 Thd. (Gr. 5) 74 781-0498 N Fuel Tank Support Brkt.
36 781-051OA N Shredder Frame (645, 648) (650, 651)
781-0459A Shredder Frame (650, 651) — 764-0199A Bag (Not Shown)
37 710-0157 Hex Bolt 5/16-24 X . 75" Lg. — 723-0400 Safety Glasses (Not Shown)
tUsed with 10 X 2.5 Wheel (Plastic—Part No. 734-1600).
ttUsed with 1 0 x 4 Wheel (Steel—Part No. 734-1597).
*For faster service obtain standard nuts, boits and washers locally.
If these items cannot be obtained locally, order by part number
and size as shown on parts iist.
CODE: N notates a new part (not previously existing).
COLOR: A three digit number is the color code. Specify color
code if coior or finish is important when ordering parts, [i.e.,
(part no.)-638 for Red Finish]
11
Color Codes
436—Radiant Yellow 638—Red
460—Green Flake 640—Green
483—Charcoal Gray 646—CM Blue
498—Yellow 650—Red Metallic
499—Beige 657—Teal
629—Silver Flake
637—Black 663—Dark Teal