Note, Lamp indicator temp indicator, Temp indicator – Panasonic PT-AE1000 User Manual

Page 21: I cleaning the outer surface of the projector, I cleaning the lens surface, I cleaning the air filter, Replacing the air filter, Temp and lamp indicators, Care and replacement, Nglish

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

TEMP and LAMP Indicators

It a problem should occur with the projector, the

TEMP

and/or

LAMP

indicators will alert you. Respond to the alert

as follows.

1. Confirm the POWER indicator status and turn off the projector in the proper way.

2. Find out the cause of the problem.

3. Follow the instructions for each indication below and solve the problem.

4. Turn on the projector in the correct way and confirm the indicator is

not

indicating a problem any longer.

NOTE:

• If problem is

found

or the problem remains, do not turn on the projector. Instead contact an Authorised

Service Centre.

LAMP indicator

TEMP indicator

indicator and

projector

Problem

• Illuminating

RED

and

still

projecting

• Flashing

RED

and

POWER

is turned off

The

temperature inside

and/or

outside

the

projector

abnormally high

Cause

The ventilation ports are
covered.

The room temperature is too

high.

The

Air filter

is excessively

dirty and the ventilation is
poor.

Remedy

Remove

the

object(s) from

the

ventilation ports or clear

around the projector.

Reinstall the projector at a

temperature controlled place.

See “Setting

up” on page 14.

Clean or replace the

Air filter

in the proper way. See

“Cleaning the Air filter” on
page 41.

LAMP indicator

Indicator
Problem

Cause

Remedy

• Illuminating

RED

• Flashing

RED

LAMP

RUNTIME

has reached 1 800 hours

(with

LAMP POWER

set to

NORMAL).

LAMP

circuit failure, abnormal function or

LAMP

damaged.

Lamp

unit

will run out soon and needs to be

I replaced.

The

projector is switched off incorrectly.

Replace

the

Lamp unit.

See “Before

replacing the Lamp unit" on

page

42.

• Let the

LAMP

cool down and turn on the

projector,

9 If the

POWER

does not turn on, contact an

Authorised Service Centre.

nglish

Care and Replacement

Ensure the projector is switched off.

• Unplug all the cables from the projector.

I Cleaning the outer surface of the projector

Wipe off dirt and dust gently with a soft cloth.

•

If it is difficult to remove the dirt, soak a cloth in a neutral detergent diluted with water, wring the cloth well

and then wipe the projector. Dry off the projector with dry cloth.

•

If you use

chemical treated wipe, follow the instructions supplied with it.

I Cleaning the lens surface

Wpe off dirt and dust gently with a lint-free cloth.

9 Make sure no dirt or dust remains on the surface of the lens. It

will

be enlarged and projected onto a

screen.

I Cleaning the Air filter

If the

Air filter

excessively

dirty, the internal temperature of

the

projector increases and may cause

malfunction. Clean the

Air filter

regularly every 100 hours of usage.

1, Place a finger at the

bottom

of the

Air filter.

Slightly

push up and

pull

out the

Air filter

to remove.

3. Vacuum dirt and dust from the

Air filter,

Do not wash the

Air filter.

4. Place and slightly slide in the

Air filter

in the

Air intake port

to attach.

• Make sure the

Air filter

clicks into the place.

NOTE:

• Do not use the projector without attaching the

Air filter.

Replacing the Air filter

The

Air filter

should be replaced when cleaning is ineffective and when replacing the

Lamp

unit.

replacement

Air filter

is provided with a replacement lamp unit, ET-LAE1000. Contact an Authorised Service

Centre for the optional

Air filter.

nglish

-41