Attwood limited warranty zamak hardware – Attwood Anchor Rein II Anchor Lift User Manual

Page 2

pulled up against the boat. Take a 3/4" wrench and tighten collar
firmly. The brake and pusher will fall into place. Screw the handle
down until you feel a slight resistance and stop. Back the handle
off, place two or three drops of oil on the threads inside the handle,
then tighten and loosen the handle few times to break-in the
threads. Do not get oil on the brake. The installation is completed.

SAFETY FEATURES TO OBSERVE IN OPERATING ANCHOR
REIN AS A BOAT REIN:

1. When untying the unit from a dock or tie-down, DO NOT

release the D-ring end and allow the rope to free-spool to the
handle. Hold to the D-ring and return the rope to the handle.

2. When tying-up your boat for extended periods of time, or as

an added precautionary and safety measure, throw a single
hand-hitch, with the rope, over the handle and draw tight.
This will assure you of a safer tie-down until your return.

3. One of the characteristics of nylon rope is that it stretches

some with use, especially when wet. If the bead does not
return completely to the handle, it is not the spring losing its
strength but rather the rope that has stretched. DO NOT cut
off rope, allow it to dry a few hours and it will return to the spool.

METHOD FOR ATTACHING ANCHOR REIN ROPE
TO ANCHOR:

1. Pull out enough rope to make a six inch loop.

2. Stick loop through eye of anchor.

3. Drop head/D-ring assembly through loop.

4. Draw loop tight. Your anchor is secured.

5. Reverse procedure to remove anchor from rope.

ATTWOOD LIMITED WARRANTY

ZAMAK HARDWARE

ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan
49331, (‘Attwood’) warrants the original consumer purchaser that
any ZAMAK Hardware will be free from defects in material and
workmanship and also that any Perma-Plate

part will be free from

corrosion under normal use and service for a period of two (2) years
from the date of original consumer purchase. This limited warranty
does not extend to any electric light bulbs for lamps, sealed beam
units, batteries or fuses. This limited warranty is not applicable if the
product has been damaged by accident, improper installation,
unreasonable use, lack of proper maintenance, unauthorized
repairs or modifications, or other causes not arising out of defects in
materials and workmanship.

Attwood’s obligations under this warranty are limited to repair of the
product at Attwood’s plant or replacement of the product at
Attwood’s option and Attwood’s expense. Any expenses involved in
the removal, reinstallation, or transportation of the product are not
covered by this warranty. The product must be returned to Attwood’s
plant at the address indicated above, postage prepaid, with proof of
original purchase, including date. If Attwood is unable to replace the
product and repair is not commercially practicable or cannot be
timely made, or if the original consumer purchaser is willing to
accept a refund in lieu of repair or replacement, Attwood may refund
the purchase price, less an amount for depreciation. The
acceptance by Attwood of any product returned or any refund
provided by Attwood shall not be deemed an admission that the
product is defective or in violation of any warranty.

THIS WARRANTY IS ATTWOOD’S ONLY EXPRESS WARRANTY
OF THIS PRODUCT. NO IMPLIED WARRANTY SHALL EXTEND
BEYOND TWO (2) YEARS FROM THE DATE OF ORIGINAL
CONSUMER PURCHASE. ATTWOOD SHALL NOT BE LIABLE
FOR ANY DAMAGES FOR LOSS OF USE OF THE PRODUCT,
NOR FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL
DAMAGES, COSTS OR EXPENSES.

Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of exclusions may not
apply to you. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

Figure 3