Canon REALiS X600 - Manual (Page 34)

User Command Specifications 9. Details of command ASPECT
1 ASPECT
ASPECT
ASPECT=：ＩＤ>
Screen setting parameters
Auto
Normal
Wide
Full screen
Real
-1
A "busy" response is given while the zoom or focus lens is being driven.
Furthermore, it may not be possible to execute the command with some input signals.
-2
-3
Menu
[Display settings] - [Screen settings]
[Display settings] - [Aspect ratio]
-4
Setting
> ASPECT=WIDE This sets the screen size to WIDE.
> i:OK
Reference
> GET ASPECT or ?ASPECT This retrieves the screen size.
< g:ASPECT=TRUE
Acquisition of parameters which can be set
> RANGE ASPECT
< r:ASPECT=I, AUTO, NORMAL, WIDE
* Commands are indicated by ">", and responses are indicated by "<".
Supported Command States
OFF ON PM
Ч ○ Ч
Ч ○ Ч
Ч ○ Ч
Ч ○ Ч
Ч ○ Ч
Ч ○ Ч
Ч ○ Ч
Ч ○ Ч
Ч ○ Ч ▼
* If the command cannot be supported, 'INVALID_MODE,' 'NOT_POWER_SUPPLIED' or 'INVALID_SOURCE' is returned as an error response.
* If the necessary signals are not input, 'INVALID_SIGNAL (*****)' or 'NO_SIGNAL' is returned.
* "i:BUSY" may be returned if the power status is being switched.
This sets the screen sizes.
SX6
SX60
Model
SX50
It can be executed when the projector is in both the remote mode and power-on status at the
same time.
The final screen settings are retained even when the power is turned off. However, the screen
settings may be different if the input terminal or input signal is changed.
This command is the same as the menu functions in the table below.
SX60 X600
"AUTO," "NORMAL" or "WIDE" can be set as the
screen size.
The GET command can be used to retrieve the current screen display mode.
X600
– ○
SX50 SX6
01.00** 01.01** 01.01** 01.01**
○ ○ Ч Ч – AUTO Ч Ч Ч
Commands
Function
Parameter
Errors supported by model
Parameter Meaning
SX50 SX6 SX60
Mode
○
○
○
○
Screen settings
"i:OK" is returned if the parameter was set properly.
FULL
Description
Response
○ ○ ○ ID
X600
SCART None
Parameter Power Input
Remote Local
Mode
D-RGB A-RGB1 A-RGB2 Comp Video S-Video D-Video
NORMAL ○ ○ ○ ○ Ч ○ ○ ○ –
○ ○
– ○
○
○ Ч ○ ○ ○ –
Ч Ч Ч Ч – ○ ○
○ Ч Ч ○ Ч ○ ○
Ч ○
Ч
Model
TRUE ○ ○
○
– ×
○ ○ ○ ○
TRUE ○ ○ ○
○ ○ ○
Ч Ч
○ ○ ○
Format
SX60
Ч Ч ○ Ч Ч Ч
AUTO ○ ○ ○
○ – –
WIDE ○ ○ ○
×
FULL ○ ○ ○ Ч Ч Ч –
–
–
○ ○ Ч
○
SX50
AUTO ○ ○
WIDE ○ ○
WIDE ○
○ ×
SX6
○ ○ ○ ○ X600 FULL ○
Control Setting Reference
The parameters which can be set at any given point in time can be obtained using the
RANGE command.
–
TRUE ○ ○ ○
NORMAL
Commands
supported
For details, refer to the RANGE command.
For all other responses, refer to "Error List."
(Refer to the ZCONTDRV command and FCONTDRV command.)
For details, refer to the GET command.
○ ○ ○ ○
Example
PAGE 26