Cooper Instruments & Systems DFI INFINITY B Ultra High Performance Digital Force Indicator - Manual (Page 74)

30.0 LOCKOUT (ACCESS SECURITY) CONFIGURATION MENU
• To prevent unauthorized tampering with the setup parameters, this instrument provides protection by requiring the user
to enter the ID (Access Security) Code before allowing access any locked menu item on Main menu.
• The locked menu will be skipped and invisible during Menu Navigation, however Display will show the locked setpoint
and value but editing mode is disabled (first digit is not flashing).
• Whether multiple or single menu accessibility/restriction desired, there is only one ID code needed.
LCk.CNF
ENTER LOCKOUT (ACCESS SECURITY) CONFIGURATION MENU:
Press ‘MENU’ 1) Ten times, Display shows "LCk.CNF" Lockout (Access Security) Configuration Menu.
Press ‘RESET/ENTER’ 2) Display shows "Id" Access Security ID menu.
Press ‘RESET/ENTER’ 3) Display shows 4 numbers 0 (0000) with the first digit flashing.
Press ‘▲/MAX’ & ‘►/MIN’ 4) To enter Access Security ID code.
• The default code is any 4-digit number that has the sum of its 4 digits equal 10. For
example 1234 is one of the default ID code since 1+2+3+4 = 10.
• Use numbers that are easy for you to remember. If the ID Code is forgotten or lost,
Call customer service with your serial number to access and reset to the default ID
code.
Press ‘RESET/ENTER’ 5) Display shows "CHNG. Id" Change ID Code menu; which Implies that the ID code,
was just entered, is accepted otherwise the meter will return to “Id" ID Code menu and
allows user enter the ID code again if the correct ID code still is not found for over 3
attempts then display shows "ERROR" and advances to "RUN" Run mode.
Press ‘RESET/ENTER’ 6) Display shows 4 numbers 0 (0000) with the first digit flashing.
Press ‘▲/MAX’ & ‘►/MIN’ 7) To modify and enter new ID code if necessary, otherwise skip this menu by Press
‘RESET/ENTER’ again.
LOCk
Press ‘RESET/ENTER’ 8) Display shows "StOREd" stored message momentarily and then advances to the
"LOCk" Lockout menu.
Press ‘RESET/ENTER’ 9) Display shows "SP1" Setpoint 1 submenu. If necessary, use ‘MENU’ button to regain
accessibility or lockout the other following menu functions in the Main Menu: "SP2",
"SP3", "SP4", "INPUt", "RdG.CNF", "INP.CNF", "MP.SC.OF", "OUt.CNF", "SP.CNF",
"AL.CNF", "COMM" (If Communication Option Board installed), and "COLOR".
Press ‘RESET/ENTER’ 10) Display flashes "dISAbL" disable option or previous setting.
Press ‘▲/MAX’ 11) Scroll and select "ENAbLE" to lockout "SP1" Setpoint 1 from any unauthorized
modification or skip this menu, just Press ‘RESET/ENTER’.
Press ‘RESET/ENTER’ 12) Display shows "StOREd" stored message momentarily and then advances to the
"SP2" submenu that allows user to lockout or regain access controlling Setpoint 2 level.
• To lockout these following sequential submenus, refer to the above steps. These
menus have the identical setup procedure and items as submenu "SP1" Setpoint 1:
"SP2": Setpoint 2
"SP3": Setpoint 3
"SP4": Setpoint 4
"INPUt": Input Selection
"RdG.CNF": Reading Configuration
"INP.CNF": Input Configuration
"MP.SC.OF": Multi Scale & Offset
"OUt.CNF": Output Configuration
"SP.CNF": Setpoint Configuration
"AL.CNF": Alarm Configuration
"COMM": Communication Configuration
"COLOR": Color Selection.
31.0 EXTERNAL CONTROL LINES
P2, the 20-pin connector at the rear of the main board, connects to the setpoint transistor collectors and permits remote
control of significant meter features.
CF 156 69 M2544/N/0505