Balboa Water Group VS-Series Configuration Guide - Manual

Output Features Quadrant
J23 + W1 – 2-Speed Pump 1 4-A
– OR 1-Speed Pump 1 with DIP Switch A5
J50 + W4 – Audio Visual - always hot, no relay 6-A
J17/26 + W7 – 1-Speed Blower (W3 to J46) 6-B
– OR Single-Speed Pump 2 or Pump 3 (W3 to J62)
J47 + W2 – Circ Pump 8-A
J29 + W2 – Ozone (Same voltage as Circ Pump, if used) 9-A
– Note X-03 option board for retro fit
J20 – Spa Light (12V only) 9-A
System can be factory configured for either a Duplex Topside Panel,
a Serial Standard Panel, or a Serial Deluxe Panel.
Note: Some panels styles are not available depending on system
configuration. Consult your Balboa product representative for details.
120V Conversion Option - Add jumper from Red AC (J32) to White AC (J11)
and set DIP switch A10 to ON.
X-P
Used for a 1-speed Pump output.
X-P231
Can replace the X-P in cases where branch circuit
protection is needed for high amperage devices that
would over-burden power input fuse F5 (1-A) on the
main PCBA.
• J6 on the X-P231 connects directly to Black AC by
using J66 or J65 on the main board (1-B).
• Connect J7 wire on the X-P231 to J60 on the main
board (7-E).
• Connect W1 on the X-P231 to Red AC on the main
board (2-D).
X-2SP Kit
Adapter PN 25339 is used in conjuction with an X-O3 to
run a 2-speed pump 2. No Blower is available when this kit is used.
• J4 connects to Black AC (3-A) using J61 or J62 on main board.
• Connect 2-speed pump to J7 on X-03. PN 53913
G C
G C
J6
J7
J4 J5
J2
W12
K1
VS500Z Configuration Guide
VS500Z Expander Board Options
Instruments
Balboa
Incorporated
VS-P2 Adapter Wire
PN 25339
To J5 on X-O3
To J17/26
(Blower/P2)
PN 53544
PN 53681
X-P332
Used for an additional 2-speed Pump output.
• J6 on the X-P332 connects directly to Black AC by
using J66 or J65 on the main board (1-B).
• Connect J7 wire on the X-P332 to J13 on the main
board (9-E).
• Connect W1 on the X-P332 to Red AC on the main
board (2-D). PN 55137
X-Mount P
Used for mounting any Expander Board
in a plastic enclosure.
Standoffs attach to heater mounting bracket. PN 53933
Document PN 40540_M
1-30-2007
A
B
C
D
E
A
B
C
D
E
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
NOTE Regarding J12 (Quadrant 9-D):
When J12 on the Main Board is jumpered on
pins 2 & 3, the system is in VS50xZ compatibility
mode.
If J12 on the Main Board is jumpered on pins 1 & 2,
the system is in VS51xZ/VS5xxSZ/VS5xxDZ
compatibility mode.
G C
J6
J4
J2
W12
K1
G C
J6
J3
J2
W12
K1
F10A 250V
F5
X-B
Used for a Blower output ONLY. PN 53310
G
R
B
W
J1
W1
J7
J6
F30A 480V
X-P231
PN 53681
P/N 22909 REV B
G
R
B
W
J1
W1
J7
J6
F30A 480V
X-P332
PN 55137
P/N 22909 REV B
G
C
G
C
G
C
G
C
C
G
RED AC
WHT AC
BLK AC
J32
J61 J62
T1
SWITCHBANK A
J11
J66 J65
J15 J16 J25 J63 J64
J33 J34
J36 J37
J35
BALBOA INSTRUMENTS, INC.
VS500Z
P/N 22972 REV D
MADE IN U.S.A
COPYRIGHT 2005
S1
J6 J7 J8
J44 J60 J22
U4
HTR2 HTR1
J101 J100
TB1
FUSE .3A 250V
FUSE 20A 250V
FUSE 3A 250V
E.GND
CLASS G FUSE 30A F5
F4
K6
K1
K8
K9
K5
J23
J74
J73
J46
F1
J29 J47
J50
F7
J17/26
J20
J1A
J10
J13
J2A
EXT.
RLY
TST
AUX. F
SEN. A SEN. B
VAC
W1
W7
W10
J1
J2
W2
W3
G
C
W4
K4
K2
K3
Balboa
F2
J12
1 2 3
J43
2-SPD
EXT RLY
J18 TORQUE
RANGE
FOR TB1:
27-30 IN. LBS.
HOT
BLACK
NEUTRAL
WHITE
HOT RED