WINGITS Grab Bar GBW40 User Manual
Page 2
Toll Free: 877-894-6448
www.wingits.com • [email protected]
W
ING
I
T
INNOVATIONS
The Solutions Company
™
View Installation Videos at:
www.wingits.com
Installing Non-Grab Bars from WINGITS
®
Confirm the Grab Bar compatibility with WINGITS
®
Toll Free: 877-894-6448
The WINGITS
®
must be assembled to the Grab Bar prior to inserting
into the wall as the installation must be more precise.
The FACEPLATE hole alignment to the grab bar flange hole must
be exact.
• Temporary attach the WINGITS
®
to the Grab Bar
• Remove the liner from the 3M WATERPROOF ADHESIVE on the
WINGITS
®
• Insert the WINGITS
®
using the Grab Bar as a template
• Push on Grab Bar for 1/2 a minute to adhere WINGITS
®
to the wall
• Remove Grab Bar
• Activate and tighten the WINGITS
®
as stated in Steps 2-8 above
Installing Grab Bars from WINGITS
®
:
1. Drill 1-1/4” hole in wall where you want to place the flange.
2. Remove the liner from the 3M WATERPROOF ADHESIVE on
the WINGITS
®
.
3. Back-out the center SCREW about the same
distance as the wall thickness.
4. Insert the WINGITS
®
into the wall with the holes aligned
vertically (12 and 6 o’clock).
5. Hold down firmly, allowing the adhesive to stick.
6. Push the screw head to the FACEPLATE to “POP” the wings
behind the wall.
7. Pull on the screw head and tighten the screw.
8. WINGITS
®
Grab Bar Flanges have 3 holes and two slots in each
flange. Use the two slots to attach the grab bar to FACEPLATE.
Attach the Grab Bar with the supplied 10-32 X 3/16” screws.
INSTALLATION
HOLES
FACEPLATE
WINGS
SCREW
3M WATERPROOF
ADHESIVE
W
ING
I
TS
®
WINGITS® 18/8 Stainless Steel Grab Bar
Mount with 2 Screws
Top and Bottom
Toll Free: 877-894-6448
www.wingits.com • [email protected]
W
ING
I
T
INNOVATIONS
The Solutions Company
™
View Installation Videos at:
www.wingits.com
Installing Non-Grab Bars from WINGITS
®
Confirm the Grab Bar compatibility with WINGITS
®
Toll Free: 877-894-6448
The WINGITS
®
must be assembled to the Grab Bar prior to inserting
into the wall as the installation must be more precise.
The FACEPLATE hole alignment to the grab bar flange hole must
be exact.
• Temporary attach the WINGITS
®
to the Grab Bar
• Remove the liner from the 3M WATERPROOF ADHESIVE on the
WINGITS
®
• Insert the WINGITS
®
using the Grab Bar as a template
• Push on Grab Bar for 1/2 a minute to adhere WINGITS
®
to the wall
• Remove Grab Bar
• Activate and tighten the WINGITS
®
as stated in Steps 2-8 above
Installing Grab Bars from WINGITS
®
:
1. Drill 1-1/4” hole in wall where you want to place the flange.
2. Remove the liner from the 3M WATERPROOF ADHESIVE on
the WINGITS
®
.
3. Back-out the center SCREW about the same
distance as the wall thickness.
4. Insert the WINGITS
®
into the wall with the holes aligned
vertically (12 and 6 o’clock).
5. Hold down firmly, allowing the adhesive to stick.
6. Push the screw head to the FACEPLATE to “POP” the wings
behind the wall.
7. Pull on the screw head and tighten the screw.
8. WINGITS
®
Grab Bar Flanges have 3 holes and two slots in each
flange. Use the two slots to attach the grab bar to FACEPLATE.
Attach the Grab Bar with the supplied 10-32 X 3/16” screws.
INSTALLATION
HOLES
FACEPLATE
WINGS
SCREW
3M WATERPROOF
ADHESIVE
W
ING
I
TS
®
WINGITS® 18/8 Stainless Steel Grab Bar
Mount with 2 Screws
Top and Bottom
Toll Free: 877-894-6448
www.wingits.com • [email protected]
W
ING
I
T
INNOVATIONS
The Solutions Company
™
View Installation Videos at:
www.wingits.com
Installing Non-Grab Bars from WINGITS
®
Confirm the Grab Bar compatibility with WINGITS
®
Toll Free: 877-894-6448
The WINGITS
®
must be assembled to the Grab Bar prior to inserting
into the wall as the installation must be more precise.
The FACEPLATE hole alignment to the grab bar flange hole must
be exact.
• Temporary attach the WINGITS
®
to the Grab Bar
• Remove the liner from the 3M WATERPROOF ADHESIVE on the
WINGITS
®
• Insert the WINGITS
®
using the Grab Bar as a template
• Push on Grab Bar for 1/2 a minute to adhere WINGITS
®
to the wall
• Remove Grab Bar
• Activate and tighten the WINGITS
®
as stated in Steps 2-8 above
Installing Grab Bars from WINGITS
®
:
1. Drill 1-1/4” hole in wall where you want to place the flange.
2. Remove the liner from the 3M WATERPROOF ADHESIVE on
the WINGITS
®
.
3. Back-out the center SCREW about the same
distance as the wall thickness.
4. Insert the WINGITS
®
into the wall with the holes aligned
vertically (12 and 6 o’clock).
5. Hold down firmly, allowing the adhesive to stick.
6. Push the screw head to the FACEPLATE to “POP” the wings
behind the wall.
7. Pull on the screw head and tighten the screw.
8. WINGITS
®
Grab Bar Flanges have 3 holes and two slots in each
flange. Use the two slots to attach the grab bar to FACEPLATE.
Attach the Grab Bar with the supplied 10-32 X 3/16” screws.
INSTALLATION
HOLES
FACEPLATE
WINGS
SCREW
3M WATERPROOF
ADHESIVE
W
ING
I
TS
®
WINGITS® 18/8 Stainless Steel Grab Bar
Mount with 2 Screws
Top and Bottom
Rev. 06062013
Rev. 06062013
Rev. 06062013