DME Front Load Square Coil Heater - Manual

90.0°
80.0°
0.7500 0.0000
+0.0005
DIA.
0.375 RAD.
0.005 LAND (MAX.)
0.030
TO SUIT 0.044 DIA. MIN.
0.187 SPH. RAD.
GATE MACHINIG DIMENSIONS
1.0000
1.250 DIA.
0.7500 0.0000
+0.0050
1.562 DIA.
1.501 0.000
+0.001
DIA.
0.770
0.31 MIN. DISTANCE BETWEEN WATERLINE
AND DROP
0.250 MIN.
0.750 MAX.
30°
"A" + BE
SEE NOTE
0.25
0.140
MANIFOLD
LINE
NOZZLE
0.125 RAD.
PLT.
WIRE SLOT
"A" PLT.
BE = 2.5 x 0.00000633 x (500 - 68) = 0.0068 . . . thus "A" + BE will be 2.5068.
ME-0741-PS-778-B SCH9999
FRONT LOAD SQUARE COIL HEATER
INSTALLATION DATA
Please read carefully before
installing and/or removing heater.
NOTE: The expansion factor must be taken into consideration prior to machining and installing nozzle. This factor (BE) must then be added to the
Please note that the above information is only given as an example. variations may occur based on mold configurations and cooling factor. In some
nominal "A" dimension. Formula for determining this expansion factor is as follows:
BE="A" dimension x 0.00000633 x(Nozzle set point temperature - 68
instances, It may be necessary to obtain an empirical factor.
F).
EXAMPLE: Given a 2.5 inch "A" dimension, with a nozzle set point temperature of 500 F:
0.634
FLAT
1.
0000
0.
38
0.635 0.000
+0.001
0.531 TYP.
WIRE SLOT
R0.26 RAD.
1.000
CIRCLE
GATE MATE 4
INTERPOLATION
NOZZLE
2.875
"B"
"L"
LEADS AFTER
FLEXIBLE
THIS AREA.
PURPOSE. IN NO EVENT SHALL D-M-E BE RESPONSIBLE FOR LOSS OF USE, REVENUE
D-M-E SHALL NOT BE LIABLE FOR MISUSE OR FAILURE TO FOLLOW THE ENCLOSED
INSTRUCTIONS AND SPECIFICATIONS. D-M-E HERBY TO DISCLAIMS ALL IMPLIED
WARRANTIES, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR
OR PROFIT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGED.
500 GMB0065
SCH2065 GMB2055 1.375
SCH1066 GMB1056 0.875
5.594 500 GMB0066
SCH2066 GMB2056 1.375
08-08
. NOTE: Dimensions are in inches
CATALOG
NUMBER
SUB-ASSY.
NUMBER
"B"
DIM.
"L"
DIM.
WATTAGE
NOZZLE
REF. NO.
SCH1060 GMB1050 0.875 1.594 250 GMB0060
SCH1061 GMB1051 0.875
2.094 300 GMB0061
SCH2061 GMB2051 1.375
SCH1062 GMB1052 0.875
2.594 350 GMB0062
SCH2062 GMB2052 1.375
SCH1063 GMB1053 0.875
3.094 400 GMB0063
SCH2063 GMB2053 1.375
SCH1064 GMB1054 0.875
3.594 425 GMB0064
SCH2064 GMB2054 1.375
SCH1065 GMB1055 0.875
4.594