Bosch TDS1229 Centro de planchado compacto SensorSteam Ultimate EAN 4242002684598 - Manual (Page 13)

13
en
Vertical steaming (8)
This can be used to remove creases from
hanging clothes, curtains etc. It cannot be used
on a synthetic setting for delicate items.
Warning!
Do not iron clothing while it is being worn!
Never spray or aim the steam at persons or
animals!
• Set the temperature control (14) to the “•••” or “max”
position and the steam control to the position.
• Hold the iron in an upright position about 15 cm
away from the garment being steamed.
• The shot of steam button (5) on the handle may
be additionally pressed at intervals of 5 seconds.
However, after 4 shots of steam, wait for 10 seconds
to allow for continued steam production.
Multiple descaling system (9)
Depending on the model, this range of irons is
equipped with the following de-scaling features
“AntiCalc”.
1. self-clean
The self-clean ilter between the water tank and the
pump prevents scale impairing the steam generation
system and ensures the optimum production of
steam.
2. anti-calc
The “anti-calc” cartridge has been designed to
reduce the build-up of scale produced during steam
ironing, helping to extend the useful life of your iron.
Nevertheless the “anti-calc” cartridge cannot prevent
all of the scale that is produced naturally over time.
3. calc’n clean
The “calc’n clean” function helps to remove scale
particles out of the steam chamber. Use this function
approximately every 2 weeks, if the water in your
area is very hard.
Follow the procedure described below:
a) Remove the plug from the socket, ensure that the
iron has cooled down and that the water tank (10)
is empty.
b) Set the temperature control (14) to the “calc‘n
clean” setting.
c) Fill the water tank (10) to the maximum level with
clean tap water.
d) Plug in the iron and select the maximum steam
setting “max” by pressing the steam selection
button (3).
e) Hold the iron over a sink or a container to collect
the water.
f) Grip the handle (1) until the water tank (10) is
empty. This could take several minutes.
g) Repeat the procedure until particles no longer
come out of the soleplate (12) of the iron.
h) Turn the temperature control (14) to the maximum
setting. The iron will begin to emit steam. Wait until
the water inside the iron has evaporated.
i) Clean the soleplate (12) of the iron.
4. calc‘n clean with descaling luid
(model dependent)
For deep descaling, use the descaling luid (16)
supplied.
This should be carried out every 3 months.
The descaling luid (16) can be obtained from our
After-sales service or from our website.
Accessory code
(After-sales)
Name of accessory
(Online shop)
311144 TDZ1101
Follow the procedure described below:
a) Remove the plug from the socket, ensure that the
iron has cooled down and that the water tank (10)
is empty.
b) Set the temperature control (14) to the “calc‘n
clean” setting.
c) Fill the water tank (10) with tap water mixed with a
measure (25 ml) of the descaling luid (16).
d) Plug in the iron and select the maximum steam
setting “max” by pressing the steam selection
button (3).
e) Hold the iron over a sink or a container to collect
the water.
f) Grip the handle (1) until the water tank (10) is
empty.This could take several minutes.
g) Then follow the procedure described above in
section “3. calc‘n clean” until particles no longer
come out of the soleplate (12) of the iron.
Anti-drip system
If the temperature control (14) is set too low (below
“••”), the steam is automatically switched off to
prevent water from dripping out of the soleplate (12).
The “ActiveControl Advanced” indicator lamp (2) on
the handle lashes and the pump will not work.