Poulan Pro PR600Y22SHP LAWN MOWER User Manual

Page 6

CAUTION: Under normal usage, the

catcher material is subject to de te ri o ra tion
and wear and should, therefore, be
checked frequently for replacement. Any
replacement catcher should be checked to
ensure compliance with original man u fac -
tur er's spec i fi

ca tions.

CAUTION: Do not run lawn mower

with out the discharge guard (rear door),
approved grass catcher, clipping de fl ec tor
or mulcher plate in place. Never attempt
to operate mower with the dis charge guard
(rear door) removed or propped open.

Hinge bracket

Formed tabs

Rear door

Grass

catcher

frame

HINGE BRACKET MOUNTED

DOOR PIVOT PIN MOUNTED

HANDLE BRACKET MOUNTED

DOOR SLOT MOUNTED

Handle bracket hooks

Rear
door

Grass

catcher

handle

Catcher frame side hook

Rear door slots

Grass

catcher

han dle

Catcher frame hook

Pivot pins

Grass

catcher

handle

Catcher frame hook

Rear
door

Frame

handle

Frame

opening

Vinyl
bindings

“FABRIC TOP” GRASS CATCHERS
TO ASSEMBLE AND ATTACH GRASS
CATCH ER
• Put grass catcher frame into grass bag

with rigid part of bag on the bottom.

• Slip vinyl bindings over frame.
NOTE: If vinyl bindings are too stiff, hold
them in warm water for a few minutes. If
bag gets wet, let it dry before using.
• Lift the rear door on the mower housing.
• For HINGE BRACKET mounted catcher,

place the grass catch er frame onto the
formed tabs on the rear door hinge
bracket.

• For HANDLE BRACKET mounted

catcher, place frame side hooks into
slots in handle brackets.

• For DOOR PIVOT PIN mounted catcher,

place the grass catcher frame hooks
onto the door pivot pins.

• For DOOR SLOT mounted catcher,

place the grass catcher frame hooks into
the slots of the rear door.

NOTE: The grass catcher is secured to the
lawn mower housing when the rear door is
lowered onto the grass catcher frame.

TURN LOWER
HANDLE OVER
TO ADJUST HEIGHT

Mowing
position

HIGH POSITION

LOW POSITION

Handle
bracket

Hairpin
cotter
Mounting
pin

LAWN MOWER

TO ADJUST CUTTING HEIGHT
See “TO ADJUST CUTTING HEIGHT” in
the Operation sec tion of this manual.

TO ADJUST HANDLE
2 POSITION HANDLES
The handle can be mounted in a high or
low po si tion. The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle.
• Remove upper handle and all parts at-

tached to lower handle.

• Remove hairpin cotters from lower

handle bracket mount ing pin.

• Squeeze lower handle in to remove it

from mounting pins.

• Turn lower handle over to raise or lower

handle.

• Squeeze lower handle in and position

holes onto mount ing pins on handle
bracket.

• Reassemble hairpin cotters onto mount-

ing pins.

• Reassemble upper handle and all parts

removed from lower handle.

3 POSITION “EZ”
The handle on your lawn mower has three
(3) height positions - adjust to height that
suits you.
• Remove knob and carriage bolt on one

side of the lower handle.

• While holding handle assembly, remove

knob and car riage bolt from opposite
side, align hole in handle with desired
hole in handle bracket and reassemble
bolt and knob and tighten securely.

• Align opposite side of handle with same

positioning hole and secure with bolt and
knob.

Handle

adjustment

bracket

Knob

Bolt

High
Med.
Low

3 POSITION “QUICK”
The handle on your lawn mower has three
(3) height positions - adjust to height that
suits you.
• Squeeze the bottom ends of lower

handle towards each other until the pin
in handle can be inserted into one of the
three height adjustment holes.

High

Handle

adjustment

bracket

Handle pin

Medium

Low

SQUEEZE