Detroit Radiant Products Company QTS Series - Manual (Page 44)

Box Part No. Description Quantity
T TP-13 Self Drilling Screws for Vent Pipe 9
B TP-33B 1/2” Shut-Off Valve (Ball Valve & Inlet Tap) 1
T TP-62 #8 - 1/2” Screw for Reflectors 16
B TP-83 24” Flexible Connector 1
B TP-6021B Tube Flange Gasket 2
B,T TP-6022 5/16” - 18 Keps Nut 9,4
T TP-6075 81” x 4” Spiral Vent Pipe 1
T TP-6080 4” Vent Adapter Fitting 1
T TP-6084A U-End Reflector End Cap 2
T TP-6085A Burner Reflector End Cap 2
T TP-6086A #8 - 1/2” Red Shoulder Screw 4
T THCS Bulldog #1 12-Ga. 60” Chain with S-Hooks 3
B LIOQTS QTS Series Installation, Operation, Parts Manual 1
Filled By:
Kit Contents Check List
5.0 Maintenance • Kit Contents Check List
B = Packed with Burner Control Box T = Packed with Emitter Assembly & Reflectors
© 2014 Detroit Radiant Products Co.
21400 Hoover Road • Warren, MI 48089
Phone: (586) 756-0950 Fax: (586) 756-2626
www.detroitradiant.com • [email protected] Printed in U. S. A.
Approvals
• CSA.
• Indoor/outdoor approval.
• Commercial approval.
Limited Warranty
• 1 year - Burner box components.
• 3 years - Radiant tubes.
• 5 years - Combustion burner.
• See page 43 for terms and conditions.
TP-33B 1/2” Shut-Off Valve
(Ball Valve & Inlet Tap)
TP-83
24” Stainless
Steel Flexible
Gas Connector
WARNING !
Improper installation, adjustment, alteration, service or maintenance can cause property
damage, injury or death. Read the installation, operation and maintenance instructions
thoroughly before installing or servicing this equipment.
This heater must be installed and serviced by trained gas installation and service personnel only. Failure to comply could result in personal injury, asphyxiation, death, fire or property
damage.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
In locations used for the storage of combustible materials, signs must be posted to specify the maximum permissible stacking height to maintain the required clearances from the
heater to the combustibles. Signs must either be posted adjacent to the heater thermostats
or in the absence of such thermostats, in a conspicuous location.
Not for residential use! Do not use this heater in the home, sleeping quarters, attached
garages, etc. Installation of a commercial tube heater system in residential indoor spaces
may result in property damage, serious injury, asphyxiation or death.
QTS Series
Installation Manual
The QTS Series Infrared Tube Heater is a negative pressure, single-stage radiant heater system.
This manual provides specific information related to the QTS Series model. All persons involved with
the installation, operation and maintenance of the heater system must read and understand the
information in this manual.
For Your Safety
If you smell gas:
• Open windows. • Do not try to light any appliance. • Do not touch any electrical switch. • Immediately call your gas supplier from a neighbor’s phone. • Extinguish any open flame. • Follow the gas supplier’s instructions. • Do not use any phone in your building. • If you cannot reach your gas supplier, call the fire
department.
Keep these instructions for future reference.
LIOQTS-Rev. 35110
Print: 1/11-r2_12/8(DRP)
Replaces: LIOQTS-8/10(DRP)
QTS Series Kit Contents
Packed with Emitter Assembly and Reflectors Packed with Burner Control Box
THCS: 60” Chain
w/ S-Hooks
LIOQTS:
QTS Series
Installation,
Operation
and Parts
Manual
TP-6022: 5/16”-18
Keps Nut
TP-6021B:
Tube Flange Gasket
TP-6080: 4” Vent
Adapter Fitting
TP-6085A: Burner
Reflector End Cap
TP-6084A: U-End
Reflector End Cap
TP-6086A:
#8 x 1/2” Red
Shoulder Screw
TP-13: Self-
Drilling Screw
TP-62: #8 x 1/2”
Screw for Reflectors