Detroit Radiant Products Company QTS Series - Manual (Page 4)

WARNING
!
DETROIT RADIANT PRODUCTS COMPANY
21400 HOOVER ROAD - WARREN, MI
RE-VERBER-RAY INFRA-RED RADIANT TUBE HEATER
FOR INDOOR (Non-Residential) INSTALLATION ONLY.
Class IIIA Permanent Label
NOT FOR RESIDENTIAL USE
(586) 756-0950 - www.drp-co.com
Line Voltage:
Control Voltage:
AMPS - Starting:
AMPS - Running:
120V - 60Hz
120V - 60Hz
1.5
1.1
Manifold Pressure:
Maximum Inlet Pressure:
Minimum Inlet Pressure:
Serial No.: 1001DETRXXXXXXXXX 0001
MODEL NO.
QTS - 80P
Heater Type
Version:
C1
3/10
INPUT BTU/H
80,000
FOR USE WITH
Propane Gas
10.0 Inches
14 Inches
11.0 Inches
W.C.
W.C.
W.C. Warning!
Unit must be
mounted level
DETROIT RADIANT PRODUCTS COMPANY 21400 HOOVER ROAD - WARREN, MI
RE-VERBER-RAY INFRA-RED RADIANT TUBE HEATER
FOR INDOOR (Non-Residential) INSTALLATION ONLY.
Class IIIA Permanent Label
NOT FOR RESIDENTIAL USE
(586) 756-0950 - www.drp-co.com
Line Voltage:
Control Voltage:
AMPS - Starting:
AMPS - Running:
120V - 60Hz
24V - 60Hz
1.5
1.1
Manifold Pressure:
Maximum Inlet Pressure:
Minimum Inlet Pressure:
Serial No.: 1001DETRXXXXXXXXX 0001
MODEL NO. QTS- 80P
Heater Type
Version:
C1
3/10
INPUT BTU/H 80,000 FOR USE WITH Propane Gas
10.0 Inches
14 Inches
11.0 Inches
W.C.
W.C.
W.C. Warning!
Unit must be mounted level
Rear Panel
F/N: LL01 - Clearance Safety Tag
(Affix adjacent to heater’s thermostat)
Rating Plate
F/N: LLTB036
SERVICE ACCESS PANEL
1. Turn off gas & electricity.
2. Remove service access panel screws.
3. Slide panel downward.
SA
MP
LE
LLTB014-5M-6/13 (CDS)
Avoid Equipment Failure.
Do Not Rotate
Burner Assembly.
Mount Level
! INSTALLER
F/N: LLTB014
Mount Level
SERVICE ACCESS PANEL
FAN, BURNER & IGNITER COMPARTMENT
1. Turn off gas & electricity.
2. Remove 1/4 inch sheet metal screws.
3. Remove cover by lifting top.
CAUTION: HOT SURFACE.
KEEP COVER IN PLACE. REMOVE FOR SERVICE ONLY.
F/N: LLTB035
(Located on top panel)
F/N: LLAC
Air Metering Orifice
Air Metering Orifice
DO NOT REMOVE
TP-3014 3"
SAMPLE
F/N: LLTB037
F/N: LLTB018 (Natural Gas)
F/N: LLTB019 (LP Gas)
QTS Series
4
1.0 Introduction • Data Labels and Their Locations
Data Labels and Their Locations
All labels must be maintained on the radiant tube heater and should be replaced if they become illegible.
Contact either your local distributor or the product manufacturer for obtaining replacement signs or labels.
It is important to provide warnings to alert individuals to potential hazards and safety actions. In locations
used for the storage of combustible materials, post a placard “specifying the maximum permissible
stacking height to maintain the required clearances from the heater to the combustibles” near the heaters
thermostat or in absence of such thermostats in a conspicuous location. Contact Detroit Radiant Products
or an authorized dealer for Clearance Safety Limit Signs or for Clearance Safety Limit Tags (one tag is
provided with each heater).
Improper installation, adjustment, alteration, service or maintenance can cause
property damage, serious injury or death. Read and understand, the installation,
operating and maintenance instructions thoroughly before installing or servicing this
equipment. Only trained, qualified gas installation and service personnel may install or
service this equipment.