Asus K8N4-E SE - Manual (Page 38)

1 - 2 6 1 - 2 6 1 - 2 6 1 - 2 6 1 - 2 6 C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
3 . 3 . 3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s
( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] , S A T A 3 [ b l a c k ] ,
( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] , S A T A 3 [ b l a c k ] , ( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] , S A T A 3 [ b l a c k ] , ( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] , S A T A 3 [ b l a c k ] , ( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] , S A T A 3 [ b l a c k ] ,
S A T A 4 [ b l a c k ] )
S A T A 4 [ b l a c k ] ) S A T A 4 [ b l a c k ] ) S A T A 4 [ b l a c k ] ) S A T A 4 [ b l a c k ] )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create RAID 0,
RAID 1, RAID 1+0, or JBOD configuration. Refer to the RAID manual in
the support CD. See page 3-5.
I m p o r t a n t n o t e o n S e r i a l A T A I m p o r t a n t n o t e o n S e r i a l A T A I m p o r t a n t n o t e o n S e r i a l A T A I m p o r t a n t n o t e o n S e r i a l A T A I m p o r t a n t n o t e o n S e r i a l A T A
The actual data transfer rate depends on the speed of Serial ATA hard
disks installed.
These connectors are set to S A T A S A T A S A T A S A T A S A T A by default. In SATA mode, you can
connect Serial ATA boot or data hard disk drives to these connectors. If
you intend to create a Serial ATA RAID set using these connectors,
enable the R A I D
R A I D R A I D R A I D R A I D function of each port from the N V R A I D N V R A I D N V R A I D N V R A I D N V R A I D
c o n f i g u r a t i o n c o n f i g u r a t i o n c o n f i g u r a t i o n c o n f i g u r a t i o n c o n f i g u r a t i o n sub-item in the BIOS. See section “2.4.4 Onboard
Devices Configuration” for details.
K8N4-E SE
®
K8N4-E SE SATA connectors
SATA4
SATA3
SATA2
SATA1
GND
RSA
T A_TXP4
RSA
T A_TXN4
GND
RSA
T A_RXP4
RSA
T
A_RXN4
GND
GND
RSA
T A_TXP3
RSA
T A_TXN3
GND
RSA
T A_RXP3
RSA
T
A_RXN3
GND
GND
RSA
T
A_TXP2
RSA
T A_TXN2
GND
RSA
T A_RXP2
RSA
T
A_RXN2
GND
GND
RSA
T
A_TXP1
RSA
T A_TXN1
GND
RSA
T A_RXP1
RSA
T
A_RXN1
GND