Waterford Appliances E65-NG1 - Manual (Page 8)

8 Waterford E65-1 Emerald Direct Vent Freestanding Gas Stove
OPTIONAL FAN INSTALLATION
Diagram 1
Diagram 2
INSTALLATION
LOCATING YOUR
EMERALD GAS STOVE
When selecting a location for your stove, en-
sure that the clearances listed above are met as
well as ensuring that there is adequate acces-
sibility for servicing and proper operation.
MANUFACTURED
MOBILE HOME
ADDITIONAL
REQUIREMENTS
1) Ensure that structural members are not cut
or weakened during installation.
2) Ensure proper grounding using the #8
ground lug provided.
3) Appliance must be anchored to the floor
with the supplied anchoring methods.
COMBUSTION AND
VENTILATION AIR
The combustion air from this appliance is drawn
from outside the building through the outer flue.
Extra provision for combustion air inside
the room is not required.
A) Cross Corner
B) Room Divider
C) Island
D) Flat on Wall
E) Flat on Wall Corner
F) Flush with Wall/Alcove
For Vent Termination requirements,
see page 10.
Fan Kit Contains:
Qty. Description
1 Fan Speed Controller with nut, and knob.
1 Fan Assembly c/w green wire attached
1 power cord
1 Plastic locking grommet
1) Remove the Top Control Panel Assembly by
removing the three screws. Diagram 1.
2) Remove the nylon hole plug from the control
panel.
3) Install the fan speed controller onto the
control panel and secure with nut. Connect
remaining wire harness wires to speed
control. NOTE: Speed control wires must
be in the down position when control panel
is in place.
4) Push black knob onto speed control.
5) Remove the rear access panel on the back
of the stove by removing the 6 screws.
Install the fan onto pins as per diagram 2.
NOTE: Do NOT damage, cut or remove
the 3" aluminum air intake pipes.
Hint for pushing fan down onto pins - rub a
bit of dish soap on the pins so the grom-
mets will slide down more easily. Check to
make sure the fan is seated properly on the
pins - try to move the fan back and forth.
6) Push power cord through hole in the rear
panel 14" - 16" and tie a loose knot in the cord
on the inside to prevent the power cord
from being pulled out. Diagram 2.
7) Install locking grommet to power cord and
push through hole in the rear panel and give
a 1/4 turn to secure.
NOTE: When running wires, keep them
clear of valve assembly and tub-
ing to avoid tangling of wires and
valve.
NOTE: Be careful not to cut wires when
passing through holes in the fire-
box.
8) Run green ground wire from fan and con-
nect to grounding lug.
9) Connect green power cord ground wire to
grounding lug.
10) Run the neutral black wire from power cord
and connect to fan motor.
11) Run the live black wire from power cord and
connect to speed control wire.
12) Connect the white wire of the wire harness
to the fan terminal.
NOTE: Pull excess wire next to fan to
avoid excessive heat from the fire-
box.
13) Ensure all wires are pulled away from
firebox to avoid excessive heat and secure
with stick-on wire clip.
14) Re-attach control panel with 3 screws,
reversing step 1. Re-attach rear access
panel with 6 screws, reversing step 5.
NOTE: When power cord is plugged in,
speed control is in the ON position and
stove is burning, allow 10 - 15 minutes for
the thermodisc (temperature switch) to
activate and turn on the Fan automatically.
WARNING:
Electrical Grounding Instructions
This appliance is equipped with a
three pronged (grounding) plug for
your protection against shock haz-
ard and should be plugged directly
into a properly grounded three-
prong receptacle. Do not cut or re-
move the grounding prong from
this plug.