Linear TRANS PROX Devices ACT-31D - Manual

Copyright © 2008 Linear LLC 228330 B
ACT-31D
ACT-34D
Operation
Instructions
DESCRIPTION
The ACT-31D and ACT-34D are TRANS PROX devices that
contain a radio transmitter as well as a proximity tag. Access
can be requested by pressing a TRANS PROX button to send
a wireless signal to a Linear MegaCode receiver, or by
moving the unit within two inches of a proximity reader.
The ACT-31D is a single-button miniature TRANS PROX
that sends one wireless code. The ACT-34D is a four-button
miniature TRANS PROX that sends four different wireless
codes, depending on which button is pressed.
In addition to each unit’s MegaCode radio transmission
capabilities (factory set from over a million possible ID codes),
both units contain a built-in proximity tag. The proximity tag
is factory programmed to the same ID and facility code as
the transmitter using card access 26-bit Wiegand format.
The unit’s proximity tag functions with Linear’s Model AM-PR
proximity reader.
The TRANS PROXs are powered by two Type 2016 “coin cell”
batteries. A 2-part key ring is supplied with the units.
PROGRAM TRANSMITTER INTO RECEIVER
Linear’s receivers that accept “Block Coding” can be
programmed to accept a user defi ned block of ID codes. The
ACT-31D and ACT-34D TRANS PROXs are block coded. Each
block of TRANS PROX is labeled with starting and ending
block code numbers, along with an optional facility code
number. Refer to the receiver instructions for details on how
to program the block and facility code numbers.
For non Block Coded single learning receivers, press
the desired TRANS PROX button while the receiver is in
programming mode to program that button into the receiver.
Refer to the access system instructions for details on how to
program the proximity tag into the system.
REPLACING BATTERIES
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months.
This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal
distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from
their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on
the part of Linear LLC for consequential damages arising out of or in connection with use or performance of
this product or other indirect damages with respect to loss of property, revenue, or profi t, or cost of removal,
installation, or reinstallation. All implied warranties, including implied warranties for merchantability and
implied warranties for fi tness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu
of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact
Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fi ll an important need in portable wireless
signaling. However, there are some limitations which must be observed.
• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15
devices. As such, they have limited transmitter power and therefore limited range.
• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio
signals that occur on or near their operating frequencies, regardless of code settings.
• Changes or modifi cations to the device may void FCC compliance.
• Infrequently used radio links should be tested regularly to protect against undetected interference or
fault.
• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor
or dealer, and these facts should be communicated to the ultimate users.
• This device complies with FCC Part 15 and Industry Canada Rules and Regulations. Operation is subject
to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
1 2 3
4 5
TWIST A COIN IN SLOT TO
OPEN TRANSMITTER CASE REMOVE THE BACK OF THE CASE REMOVE THE TWO
BATTERIES
SLIDE IN TWO NEW
TYPE 2016 BATTERIES
BE SURE BOTH PLUS (+)
SIDES ARE FACING AWAY
FROM THE CIRCUIT BOARD
SNAP CASE
TOGETHER
DISCARD BATTERIES
PROPERLY
ACT-34D ACT-31D
USE AS A
TRANSMITTER
USE AS A
PROXIMITY TAG
LINEAR
MODEL
AM-PR
TRANS PROX
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,ACT-31D/34D; LINEAR P/N: 228330 B; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 5.500”; SCALE: 1-1
PROX TRANS
Integrated transmitter
& proximity tag