LG WM3001H*A - Manual (Page 27)

w
WARNING:
• Unplug the washer before cleaning to avoid the risk of electric shock. Failure to follow this warning
can cause serious injury, fire, electrical shock, or death.
• Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer.
They will damage the finish.
REgULAR CLEANINg
C A R E A N D C L E A N I N G
Removing Lime Buildup
If you live in an area with hard water, lime scale
can form on internal components of the washer.
Use of a water softener is recommended in areas
with hard water. If a descaler is used, make sure
that it is suitable for use in a washer, and run the
TUB CLEAN cycle before washing clothing.
Lime scale and other spots may be removed
from the stainless steel drum using a stainless
steel cleaner. Do NOT use steel wool or abrasive
cleansers; they can damage the surface.
Storing the Washer
If the washer will not be used for an extended
period of time and is in an area that could be
exposed to freezing temperatures:
Turn off water supply tap.
Disconnect hoses from water supply and
drain water from hoses.
Plug the power cord into a properly grounded
electrical outlet.
Add 1 gallon of nontoxic recreational vehicle
(RV) antifreeze to the empty wash drum.
Close door.
Select the spin cycle and let washer spin
for 1 minute to drain out all the water.
NOTE: Not all of the RV antifreeze will be
expelled.
1
2
3
4
5
Unplug the power cord, dry the drum interior
with a soft cloth, and close the door.
Remove the inserts from the dispenser. Drain
any water in compartments and dry the
compartments.
Store the washer in an upright position.
To remove the antifreeze from the washer
after storage, run washer through a complete
cycle using detergent. Do not add laundry!
6
7
8
9
Cleaning the Exterior
Proper care of your washer can extend its life. The outside
of the machine can be cleaned with warm water and a mild,
nonabrasive household detergent.
Immediately wipe off any spills with a soft, damp cloth.
IMPORTANT: Do not use methylated spirits, solvents, or
similar products.
Never use steel wool or abrasive cleansers; they can damage
the surface.
Care and Cleaning of the Interior
Use a towel or soft cloth to wipe around the washer door
opening, door seal, and door glass. These areas should be
kept clean to ensure a watertight seal. Be sure to wipe under
the inside rubber seal to remove any moisture or soil.
Always remove items from the washer as soon
as the cycle is completed. Leaving damp items in the washer
can cause wrinkling, color transfer, and odor.
Run the TUB CLEAN cycle regularly to remove detergent
buildup and other residue.
Cleaning the Steam and Water
Circulation Nozzles
Use a cotton swab to remove lime or detergent buildup from
the inside of the steam and water circulation nozzles. NEVER
use a sharp or pointed object; you could damage the nozzles.
Removing the Stain in Door Seal
NOTE: Wear rubber gloves and eye protection while
performing the following procedure:
Dilute 3/4 cup (177 ml) liquid chlorine bleach with
1 gallon (3.8 L) of warm/hot water.
1
2
3
4
Use this solution to wipe down all surfaces of
the gasket to remove the deposits that are causing
any odor. (Be sure to fold back the lip of the gasket
to get under the edge where residue can build up.)
Wipe the gasket with a dry cloth.
Leave the door open to allow the gasket to dry
completely.
Do not use undiluted bleach as this will damage the gasket.Follow
the manufacturer’s instructions for proper use of bleach.
If the gasket cannot be cleaned properly, it should be replaced.
Notice of tub clean activation
To clean up the tub, please select the tub clean
course. Please empty the tub and insert bleach
into the detergent dispenser and push the tub
clean button.
Door open recommended
It is recommended that you should leave the door
open after getting finished with laundry to keep
the tub clean.
NOTE: NOTE: If you use the TUB CLEAN cycle on a
monthly basis, the wash drum will be kept clean.
2