Shindaiwa 35701 - Manual (Page 14)

14
OPERATION
Mixing Fuel/Filling With Fuel
WARNING!
Minimize the risk of fire burns and
personal injury!
IMPORTANT!
Shindaiwa high-performance 2-cycle
engines are designed to operate on a
50:1 mixture of unleaded gasoline
and 2-cycle engine oil. Using a fuel
mixture less than 50:1 ratio (such as
80:1 or 100:1) can cause cata-
strophic engine failure!
■ STOP engine before refueling.
■ ALWAYS allow the engine to
cool before refueling!
■ ALWAYS open the fuel cap
slowly to allow any pressure
build-up in the tank to release
fuel vapor slowly.
■ Wipe all spilled fuel and move
the engine at least 10 feet (3
meters) from the fueling point
and source before restarting!
■ NEVER start or operate this
unit if there is a fuel leak.
■ NEVER start or operate this
unit if the carburetor, fuel lines,
fuel tank and/or fuel tank cap
are damaged.
■ NEVER smoke or light any
fires near the engine or fuel
source!
■ NEVER place any flammable
material near the engine
muffler!
■ NEVER operate the engine
without the muffler and spark
arrester in good working condition.
CAUTION!
Ⅵ Some types of gasoline contain
alcohol. Never use any type of
gasoline containing more than
10% alcohol by volume! More
than 10% alcohol by volume
may affect the lubricating
qualities of 2-cycle engine oils
reducing engine life and/or
causing engine failure.
Ⅵ Generic engine oil and marine
engine oil may not be intended
for use in high-performance 2-
cycle engines and should never
be used in Shindaiwa engines.
Engine oils not intended for use
high-performance air-cooled 2-
cycle engines can cause
excessive carbon deposits,
reduce engine life and/or cause
engine failure.
1. Use only fresh, clean unleaded
gasoline with a pump octane rating
of 87 or higher.
2. Mix fuel with a 2-cycle engine oil
designed for use in high-perfor-
mance 2-cycle air-cooled engines.
NOTE:
Shindaiwa offers two performance
levels of 2-cycle air-cooled engine oils,
Shindaiwa 2-Cycle Engine Oil and
Shindaiwa ONE High Performance 2-
Cycle Engine Oil. Shindaiwa 2-Cycle
Engine Oil is designed to meet the
lubrication demands of most 2-cycle
air-cooled engines. Shindaiwa ONE
High Performance 2-Cycle Engine Oil
is recommended when superior
lubrication is needed to help protect
engines used in severe operating
conditions. Shindaiwa ONE also
contains a fuel stabilizer to help
maintain fuel quality when fuel is
stored longer than 30 days.
27
MAINTENANCE
35718
Daily Maintenance
WARNING!
Before performing any
maintenance on this saw,
stop the engine and disconnect
the spark plug wire!
■ Remove dirt and debris from the
saw exterior, cylinder fins, and
cooling air intake.
■ Inspect the saw for fuel and oil
leaks. Repair as necessary.
■ Remove
the air
cleaner
cover and
element.
Wash both
parts with
soap and
water. Let
dry before
reassembly.
CAUTION!
Never allow chips or other debris to
enter the carburetor bore! Avoid
forcing dirt into the air filter
element! When using compressed
air to dry the element, blow only on
the inside (carburetor side) face of
the element!
■ Sharpen and adjust the chain as
required.
■ Clean the guide bar groove and oil
hole. Inspect the bar groove and tip
for damage or unusual wear. Repair
or replace components as necessary.
■ Inspect the entire saw for damage,
including loose or missing compo-
nents or fastenings. Repair as
necessary.
IMPORTANT!
MAINTENANCE, REPLACEMENT,
OR REPAIR OF EMISSION CON-
TROL DEVICES AND SYSTEM MAY
BE PERFORMED BY ANY REPAIR
ESTABLISHMENT OR INDIVIDUAL.
HOWEVER, WARRANTY REPAIRS
MUST BE PERFORMED BY A
DEALER OR SERVICE CENTER
AUTHORIZED BY SHINDAIWA
KOGYO, LTD. AND USE OF PARTS
THAT ARE NOT EQUIVALENT IN
PERFORMANCE AND DURABILITY
TO AUTHORIZED PARTS MAY
IMPAIR THE EFFECTIVENESS OF
THE EMISSION CONTROL SYSTEM
AND MAY HAVE A BEARING ON
THE OUTCOME OF THE WAR-
RANTY CLAIM.