JVC G-CODE HR-S5980AJ - Manual (Page 10)

June 6, 2003 4:31 pm Page 10
— 10 —
Master Page: Right
Up to 8 timer recording programs can be made using G- CODE /
S HOW V IEW timer programing or Express timer programing method
as far as a year in advance. Remember, the clock must be set
before you can program the timer.
NOTES:
● If all the 8 programs have already been set, “PROGRAM FULL”
appears on the TV screen.
● After timer recording is completed, the recorder turns off
automatically.
● You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
● In case of a power failure after programming, the recorder’s
memory backup keeps your selections (if the lithium battery is
not exhausted).
G- CODE
TM /S HOW V IEW
TM System Setup
INFORMATION
G- CODE and S HOW V IEW are different trademarks used to represent
the same easy recording feature, but only the term G- CODE system
will be used in the instructions. If you use the S HOW V IEW system,
follow the same instructions listed for the G- CODE system.
The G- CODE timer programming system eliminates the need to
input channel, date, start and stop time data when setting the
timer record function. Simply key in the G-
CODE number for the
TV programme you wish to record (found in most TV listings) and
the recorder's timer is automatically programmed.
You have to set “GUIDE PROG” numbers, which are assigned to
each station for purposes of G-
CODE timer programming, for all
the stations stored in your recorder’s memory to get proper results.
Before G- CODE setup you must have performed the procedures of
Tuner Set and Clock Set.
IMPORTANT
Perform the following procedure after Auto Set Up and/or the
channel setting steps.
After setting the Guide Program Numbers, channel positions may
be incorrect if you stored or skipped channels. In this case, re-
perform Guide Program Number setting.
Guide Program Number Set
A
Access Main Menu screen, then Initial Set screen
Press MENU on the remote control. Press PUSH JOG rt to place
the pointer next to “INITIAL SET”, then press OK or PUSH JOG e.
B
Access G- CODE /S HOW V IEW Setup screen
Press PUSH JOG rt to place the pointer next to “G-CODE/
SHOWVIEW SETUP”, then press OK or PUSH JOG e.
C
Input Guide Prog number
Press PUSH JOG rt or the Number
keys to select the Guide Program
number as shown in the TV listing, then
press OK or PUSH JOG e.
D
Input receiving channel number
Press PUSH JOG rt or the Number
keys to select the number of the channel
on which the Guide Program number’s
broadcasts are received, then press OK
or PUSH JOG e.
● If the satellite broadcast is received on
your recorder's auxiliary channel (“L-1” or “F-1”), select “L-1”
or “F-1” for the channel position to which the satellite receiver is
connected.
● Repeat steps 3 3 3 3 and 4 4 4 4 as necessary.
E
Return to normal screen
Press MENU on the remote control.
G- CODE
TM /S HOW V IEW
TM Timer Programming
With the G- CODE system , timer programming is greatly simplified
because each TV programme has a corresponding code number
which your recorder is able to recognise.
A
Access G-CODE/SHOWVIEW NO.
screen
Press PROG.
B
Enter G- CODE number
Press the number keys to enter the
G-
CODE number of a programme you
wish to record.
● If you make a mistake, press & and
input the correct number.
C
Enter G- CODE programme screen
Press OK, and the G- CODE Programme
screen appears. (If you're just starting
out, “P1” appears.)
● If the number you entered is invalid, “ERROR” appears on the
screen. Press & and input a valid G- CODE number.
● If the “G-CODE/SHOWVIEW SETUP” screen appears, see
“ATTENTION – Regarding Guide Program Number Set”
on page 11.
D
Set tape speed
Press p to set the tape speed.
E
Access title edit screen
Press the number keys “1”. The Title Edit
screen appears.
● You can access the Title Edit screen
only when “PROG. NAVIGATION” is
set to “ON”. (
੬
15)
F
Enter programme title
Press the number keys and PUSH JOG e
to enter characters, then press OK. For
details, refer to “Entering Character” on
page 14.
G
Return to normal screen
Press PROG or OK. “PROGRAM
COMPLETED” appears on the screen for about 5 seconds, then
normal screen appears. If “PROGRAM OVERLAPPED” appears on
the screen and “Err” on the display panel, see page 13.
● Repeat steps 1 – 7 for each additional programme.
H
Engage recorder’s timer mode
Press #. The recorder turns off automatically and “#” appears on
the display panel.
● To disengage the timer, press # again.
Timer Recording
G-CODE/SHOWVIEW SETUP
[MENU] : EXIT
[0-9] OR [R/T]: SELECT
GUIDE PROG TV PROG
2 5
GUIDE PROG TV PROG
2 2
G-CODE/SHOWVIEW SETUP
[MENU] : EXIT
[0-9] OR [R/T]: SELECT
Before performing G- CODE /S HOW V IEW Timer Programming:
● Be sure to read “G-
CODE TM /S HOW V IEW TM System Setup”
(
੬
10).
● Insert a cassette with the safety tab in place. The recorder will
come on automatically.
● Turn on the TV and select the VIDEO channel (or AV mode).
● Select the appropriate colour system ( ੬
15).
IMPORTANT
Make sure the channel position number you wish to record is
displayed; if not, see “G-
CODE TM /S HOW V IEW TM System Setup” on
page 10 and set the Guide Program number for that G- CODE
number correctly.
G-CODE/SHOWVIEW NO.
[PROG] : EXIT
[+/–] : EXPRESS PROGRAMING
[0-9]
G-CODE/SHOWVIEW NO.
[PROG] : EXIT
[0-9]
1 2 3 4 5 6 7 8
[&] : DELETE
– PI –
[1] : TITLE : OK
NO. 123456789
START STOP
21:00 22:00
SP
DATE TV PROG
25.04 1
– P1 –
[PROG] : EXIT
[Y/U] : CURSOR
[&] : DELETE
[0-9] : SELECT LETTERS
: OK
25.04 21:00 PR.1
– P1 –
[PROG] : EXIT
[Y/U] : CURSOR
[&] : DELETE
[0-9] : SELECT LETTERS
: OK
25.04 W
HR-S5980AH.5980AJ_EN001B.fm Page 10 Friday, June 6, 2003 4:31 PM