FUNAI MSD126 - Manual (Page 15)

-15- EN
Functions
ENTER
DISPLAY Setting
You can change the display functions. Follow steps 1 to in the “CUSTOM Menu” section on page 14.
B
AUDIO Setting
Choose the appropriate audio settings for your equipment. It only affects during the playback of DVD discs. Follow steps 1 to
in the “CUSTOM Menu” section on page 14.
C
4
Select the desired item .
SETUP AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL ON
ON
BITSTREAM
5
Hint
TV ASPECT:
• Select “4: LETTER BOX”, so that
black bars may appear on the top
and bottom of the screen.
• Select “4: PAN & SCAN” for a
full height picture with both sides
adjusted.
• Select “16:9 WIDE” if a wide-screen
TV is connected to this unit.
STILL MODE:
• Select “AUTO” usually.
• If you select “AUTO”, automati-
cally select the best resolution setting
(FRAME or FIELD) based on the data
characteristics of the pictures. (default)
• If you select “FIELD”, the picture in
the still mode will be stabilized.
• If you select “FRAME”, the picture in
the still mode will be highly defined.
• An individual picture on TV screen
is called a “frame”, which consists of
two separate images called as “field”.
• Some pictures may be blurred if you
select “AUTO” in the still mode due
to their date characteristics.
4
Select the desired item.
DISPLAY menu
AUDIO menu
TV ASPECT: QUICK
(Default: 4:3 LETTER BOX)
See Hint on the left.
TV ASPECT
4:3 LETTER BOX
4:3 PAN & SCAN
16:9 WIDE
TV ASPECT 4:3 LETTER BOX
STILL MODE
AUTO
PROGRESSIVE OFF
STILL MODE:
(Default: AUTO)
See Hint on the left.
TV ASPECT 4:3 LETTER BOX
STILL MODE AUTO
PROGRESSIVE OFF
STILL MODE
AUTO
FIELD
FRAME
5
DRC (Dynamic Range Control):
(Default: ON)
Set to “ON” to compress the range between soft and loud sounds.
DOLBY DIGITAL: QUICK
(Default: BITSTREAM)
Set to “BITSTREAM” when the unit is connected to a Dolby Digital decoder.
• BITSTREAM: outputs a Dolby Digital Signals.
• PCM: converts the Dolby Digital into PCM (2 channel).
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
OFF
ON
BITSTREAM
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
ON
OFF
BITSTREAM
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
ON
ON
PCM
ENTER ENTER
ENTER ENTER
DOWN SAMPLING:
(Default: ON)
Set to “ON” when outputting in 48kHz.
Set to “OFF” when outputting the original sound.
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
OFF
ON
BITSTREAM
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
ON
OFF
BITSTREAM
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
ON
ON
PCM
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
OFF
ON
BITSTREAM
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
ON
OFF
BITSTREAM
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
ON
ON
PCM
Hint
DRC:
• This function is available
only on the discs which are
recorded in the Dolby Digital
format.
DOWN SAMPLING:
• When playing back a 96kHz
disc with the copyright
protection, or when Virtual
Surround is set to “1” or
“2”, the sound will be down
sampled at 48kHz and output
as digital audio even if the
“DOWN SAMPLING” is set to
“OFF”.
• This function is available
only on digital output-
ting of a disc recorded in
96khz.
SETUP DISPLAY
TV ASPECT
STILL MODE
PROGRESSIVE 4:3 LETTER BOX
AUTO
OFF
ENTER ENTER
ENTER ENTER
ENTER ENTER
6
To exit the menu
SETUP
PROGRESSIVE: QUICK
(Default: OFF)
See Hint on the right.
6
To exit
the TV ASPECT or
STILL MODE screen
To complete the
PROGRESSIVE setting
ENTER ENTER
SETUP
ENTER ENTER
ENTER ENTER
ENTER ENTER
TV ASPECT 4:3 LETTER BOX
STILL MODE AUTO
PROGRESSIVE OFF 4:3 LETTER BOX
AUTO
ON
Before proceeding…
1. Make sure your TV has progressive scan.
2. Connect with component video cable
NOTE: If there is no picture or picture is
distorted after selecting ‘YES’,
wait about 15 seconds for auto recovery.
Activate Progressive?
SELECT: K / L SET:ENTER
NO
YES
NO
YES NO
YES
Confirm again to use progressive scan.
If Picture is good, select ‘YES’.
SELECT: K / L SET:ENTER
If there is no picture
or you do not press
any buttons for 15
seconds, Progressive
scan will switch to
“OFF” and it will exit
the setup menu.
SETUP
ENTER ENTER
Hint
PROGRESSIVE:
• You can set
“PROGRESSIVE” to “OFF” in
the DISPLAY menu or press
and hold [PLAY B] on the
front of the unit for more than
5 seconds during playback,
so that the P- SCAN indicator
on the front panel lights off.
• When “PROGRESSIVE”
is “ON”, video signals from
the unit’s VIDEO OUT and
S-VIDEO OUT jacks will be
distorted or not be output at all.
Select the
desired
setting.
ENTER
Select “Yes”.
ENTER
Select “Yes”.
ENTER
Select the
desired
setting.
ENTER
ENTER
MSD126_E6AB5UD.indd 15 2006/01/06 15:26:02