Marantz DR6050 - Manual (Page 16)

11
ENGLISH
• If message also flashes, the dig-
ital connection is incorrect.
t t t t t Set the optimal recording level on the CD-Recorder.
q Play the source first to set the optimal recording level on
the CD-Recorder.
w Rotate the EASY JOG (19) key until, on the Record/Play
Level bar, all the blue segments are alight, but the red seg-
ments do not light continuously during the loudest passages.
DIGITAL RECORDING : +6dB ~ –63dB
ANALOG RECORDING : 0dB ~ –63dB
e Stop the source.
y y y y y To start recording, press 0 0 0 0 0 REC (4) on the CD-Recorder
and immediately start the source (from Stop-mode).
The track number and recording time left appear on the display.
• To record a 3-second silence at the start of a track,
press 2 / ; PLAY/PAUSE (6) on the CD-Recorder be-
fore starting the source.
• To check the elapsed recording time, press DISPLAY
(72) on the CD-Recorder. (This can also be done dur-
ing the recording.)
u u u u u To stop recording, press 9 9 9 9 9 STOP (5, 82) on the CD-Re-
corder.
• If 9 STOP (5, 82) was pressed within 3 seconds after
0 REC (4), no recording will take place.
• To interrupt recording, press 2 / ; PLAY/PAUSE (6) on
the CD-Recorder. Press
0 REC (4) to resume.
After recording the display will show for sev-
eral seconds.
Important:
If you want to play the recorded CDR disc on any regular
CD player, it must first be finalized. (See FINALIZING/
UNFINALIZING page 13.)
There is a chance that the sound will be distorted if the re-
cording level is set at a value that exceeds 0 dB for digital
sound sources and -12dB for analog sound sources. The
factory settings at the time of shipping are 0 dB for digital
sound sources and -12dB for analog sound sources.
Finalized CD-RW discs play only on CD-RW compatible CD players.
RECORDING (FROM EXTERNAL SOURCE)
The numbers between parentheses refer to the fold-out.
MENU/
STORE CANCEL/
DELETE
0
9 8 7
6 5 4
3 2 1
CD CDR
ABC DEF GHI
JKL MN OPQ
RST UVW XYZ
DISPLAY SPACE SCROLL
FUNCTION
ENTER
Recordable ReWritable
SOURCE REC TYPE
CLOSE OPEN/ CLOSE OPEN/
ERASE FINALIZE
POWER ON/OFF PLAY/PAUSE STOP
REC CDR
CD RECORDER DR6050
PLAY/PAUSE STOP
CD DJ MODE
EASY JOG
PUSH ENTER
CANCEL/DELETE STORE/MENU
PHONES
STANDBY
e r y u t
u
Manual start recording
Manual recording from external CD player.
q q q q q Make sure the disc is absolutely free of scratches and
dust particles.
w w w w w Connect the cable from an ertnal CD player to the CD-
Recorder. (see INSTALLATION page 5 and 6.)
e e e e e Press SOURCE (12) repeatedly until the selected exter-
nal source appears on the display (depending on the
connection used):
➔ , or lights up and
, or appears on
the display.
About Auto Track increment
• When Auto Track is ON (default setting), track numbers
will automatically be increased during recording.
• To switch off the Auto Track function you have to enter
MENU MODE.
If you wish to increase track numbers manually, press
TRACK INCR(ement) on the remote control. For further
instructions see MENU MODE.
ON (AUTO): The track increments are automatically
taken over from the digital source material
or after 2.7 seconds silence during analog
recording.
OFF (MANUAL): Track numbers can be incremented
manually by pressing TRACK INCR
(68) (ement) on the remote control.
(Minimum track length is 4 sec.)
• Track numbers cannot be changed after recording.
Note:
Auto track works only with Consumer Sources with a digital output
signal according to the IEC 958 (consumer part) audio standard.
r r r r r With the recorder stopped, press REC TYPE (11) five
times to enter the Manual Record standby mode.
➔ The display shows .